Best answer

The base itself should be 4″ thick in the main and 8″ thick around the outer edges. Underneath the concrete there should be a minimum 4″ of compacted hardcore. The edges of the base should be troweled off or chamferred to allow any water to drain off. Overall the base should be 3″ bigger than the building on all sides.

Answered by: Themodmin Date created: Jun 26, 2022

How thick should my concrete slab be?

Asked By: Paweł Grondal Date created: Jun 17, 2022

4 inchesStandard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks. To prepare the base, cut the ground level to the proper depth to allow for the slab thickness.

Answered By: Sven van den Boogaart Date created: Jun 17, 2022

How thick should plaster be on plasterboard?

Asked By: sawa Date created: Jun 16, 2022

You should aim for a thickness of around 1–2mm. The plaster you have mixed should last around 40 minutes before starting to set.

Answered By: Andrej Kesely Date created: Jun 16, 2022

How thick should a concrete slab be for a mobile home?

Asked By: hallski Date created: Jun 18, 2022

4 to 6 inches

Answered By: kender Date created: Jun 21, 2022

How deep should a sub base be for a concrete slab?

Asked By: Cheeso Date created: Jun 25, 2022

100mmSub-grade. The surface needs to be dug off to a depth of at least 100mm, or whatever depth is required for the proposed concrete slab. Remove all weeds and other unwanted organic matter. Excavate any soft spots and fill with compacted sub-base material.

Answered By: Alex Stone Date created: Jun 27, 2022

How thick does a concrete slab need to be for a garage?

Asked By: Mohammad Usman Date created: Jun 13, 2022

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region.

Answered By: rbaldwin Date created: Jun 14, 2022

How thick should cement board be under tile floor?

Asked By: hammar Date created: Jun 16, 2022

Floors: A 1/4-inch minimum thickness is needed, but thicker panels are also fine. Walls: Use 1/2-inch or 5/8-inch-thick cement board, not 1/4-inch. The extra thickness is needed to span the studs and provide a solid base for the tile.

Answered By: spencergibb Date created: Jun 18, 2022

What is the minimum depth for a concrete slab?

Asked By: Brian Riehman Date created: Jun 13, 2022

5 cm thickWhatever you plan on doing, your concrete slab should be at least 5 cm thick. That is the bare minimum of a concrete slab thickness. This is the thickness of the concrete slab alone and it doesn't include the gravel base, if you are using something like that.

Answered By: T.Todua Date created: Jun 15, 2022

How thick should a concrete slab be for a shed?

Asked By: Simon Wright Date created: Jun 19, 2022

Recommended Thickness of Concrete Slabs Shed Slabs: 3 1/2 inches thick. Shed floors that are being used for studio sheds or workshops will use a 3 1/2" thickness. Driveways: 4 inches, some areas require 5 inches. Many garage sheds need a driveway approaching the large shed door.

Answered By: Kit Date created: Jun 22, 2022

How thick should a concrete driveway be?

Asked By: Andrei Volgin Date created: Jun 25, 2022

four inchesAs for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.

Answered By: brian-brazil Date created: Jun 25, 2022

How deep should a concrete base be for a log cabin?

Asked By: Can Poyrazoğlu Date created: Jun 19, 2022

100mmConcrete.

A base of concrete can be done in a number of ways.

Generally it can be done with simple timber shuttering.

The average base will be about 80 – 100mm deep..

Answered By: Ahmad Date created: Jun 21, 2022

Related Question Answers

Martijn Courteaux

Professor

How deep should a concrete footing be for a retaining wall?

Concrete retaining wall footing size The depth to the bottom of the base slab should be kept at a minimum of two feet. However, it should always be below the seasonal frost line, and that often is much deeper in northern climates.

Venkatachalam

Professor

How thick should a cement driveway be?

As for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.

Nathan Kinsinger

Professor

Can I build a garage on a concrete slab?

You may want to consider a 6" thick slab for larger vehicles such as trucks or RVs. For a garage WITHOUT a floor - BUILT ON SITE: Prepare a level concrete slab at least 4” thick and to the exact, outside, dimensions of your garage. You may want to consider a 6" thick slab for larger vehicles such as trucks or RVs.

Kevin ABRIOUX

Professor

How do you prepare the ground for a concrete garage floor?

Good ground preparation starts with removing the topsoil. Then, if the soil has not previously been "disturbed" (i.e., dug up), a four-inch layer (minimum) of gravel or stone should be added. (Soil that has been dug up before should be compacted.) The gravel or stone also needs to be compacted.

Brent Bradburn

Professor

How thick should a concrete slab be for a basketball court?

3500 PSIBase Material Many basketball courts are built over a 4” thick concrete slab using 3500 PSI concrete and 1/2″ rebar reinforcements. Concrete is considered ideal for basketball courts as a permanent structure that when done right will not require any maintenance.

arshajii

Professional

How thick does the concrete need to be for a car lift?

100mmThe minimum and recommended thicknesses of concrete slab for car hoists. Garage Equipment's two and four post hoists require a minimum of 100mm (about 4”) of reinforced concrete slab to be safely installed.

Alex Wayne

Professional

How thick of a concrete slab for a hot tub?

about 4 inchesConcrete Slab The base of reinforced concrete should be about 4 inches thick and be able to withstand a weight of at least 115 pounds per square foot, especially for larger spas. The concrete should be fully cured prior to placing the tub.

Paul Hankin

Professional

What thickness cement board should I use?

Half-inch cement backer board is ideal for most tiling jobs, including walls, floors, countertops, and ceilings.

For flooring, the backer board should be installed over a 5/8-inch thick OSB or plywood base..

Fab

User

How thick should a concrete pool be?

between three and four inchesGenerally, the pool walls need to be between three and four inches thick. Smooth the pool walls with your trowel, as you did for the base. Now the concrete has to cure properly before you can fill it with water. The concrete curing process allows the concrete to reach maximum strength and takes approximately 28 days.

Itay Moav -Malimovka

User

What kind of wood should I use for a concrete base?

Using 150mm x 25mm sawn and treated timber, cut the four sides of the formwork for your base. This timber should be 300mm longer than your base and 300mm wider. Lay the timber out where you want the base and using a heavy "lump" hammer bang in some 50mm x 50mm posts along the line of the timber.

Andre.Santarosa

User

How thick should a concrete slab be for a shop?

Five to six inchesFive to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks.

To prepare the base, cut the ground level to the proper depth to allow for the slab thickness..

jm666

User

How thick should a polished concrete floor BE?

about 3 to 5 mmThey typically provide a surface layer about 3 to 5 mm thick. Precautions need to be taken to protect surrounding areas and finishes from the fine airborne particles, and breathing masks should be worn.

James Brown

Guest

How thick should a concrete fire pit be?

The optimal size for a fire pit is between 36 and 44 inches inside diameter. That will create enough room for a healthy fire but still keep gatherers close enough to chat. As an added precaution, the fire pit should be lined with a thick steel ring like the ones used for park campfires.

Roland

Guest

How thick should a concrete slab be for a pole barn?

4”Thickness – The industry standard for a residential pole barn, where you are storing lawn mowers, toys, or regular vehicles, is reinforced concrete floor that is 4” thick. If you have heavier equipment, you may want to consider flooring up to 6” thick for better wear and tear.

Renato Damas

Guest

How thick should concrete be to hoist?

100mmYour hoist has specific requirements to secure safely to a concrete base. Make sure your concrete is thick enough to support your hoist, minimum thickness is 100mm. Also, ensure your concrete is in good condition with no major cracks.

tvanfosson

Guest

How thick should my concrete driveway be?

four inchesAs for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.

Jayesh

Guest

How much does it cost for a concrete slab for a garage?

A typical concrete slab will cost between $113 and $126 per cubic yard (27 cubic feet) or $5.35 to $6.17 per square foot on average. Four to eight inch thick concrete slabs are mainly used for driveways, patios, sidewalks, and garage floors.

agabrys

Guest

How thick does a concrete garage floor need to be?

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it.

Building codes offer requirements for the concrete mix, which vary by region.

The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix..

jAndy

Guest

How thick does a concrete slab for a shed need to be?

4-inchA 4-inch slab is generally a good thickness for a typical shed. This concrete floor can be poured in most locales on a 4-inch base of compacted gravel. That requires an excavation of at least 6 inches to make a slab that will be 2 inches above the surrounding ground.

Vitalii Korsakov

Guest

How thick does concrete need to be for a shed?

A 4-inch slab is generally a good thickness for a typical shed.

This concrete floor can be poured in most locales on a 4-inch base of compacted gravel.

That requires an excavation of at least 6 inches to make a slab that will be 2 inches above the surrounding ground..

Tom Lehman

Guest

How thick should concrete be for a patio?

Four inches is the minimum thickness for a concrete patio. You'll want to make it six to eight inches thick if the patio will support a structure such as a gazebo or hot tub.

mkasberg

Guest

How thick should a concrete drive be?

For a standard driveway your sub-base should be at least 100mm deep (the same depth as the concrete), rising to 150mm if you plan to park larger vehicles on it. The hardcore sub-base needs to be in place and compacted before any ready-mix concrete arrives.

Ramis

Guest

What is the best base for concrete driveway?

gravel baseThe gravel base for a driveway should be a minimum of 4 inches deep. If heavier vehicles, such as large trucks, will use the driveway regularly, the gravel should be even deeper, up to 12 inches. Poor soil or a sloped driveway may also require deeper gravel.

shilovk

Guest

How thick should a concrete pool deck be?

4 inchesAs a general rule, you should not make a concrete deck less than 4 inches thick. This depth will keep the deck strong enough to withstand general wear and tear. You could choose to make the deck 6 inches thick for good results.

sophros

Guest

Can you use concrete as a base for pavers?

Mortar or Concrete Mix A 4- to 6-inch-thick concrete slab is suitable as a base for pavers, which can be laid directly onto the wet concrete so they are held in place when it dries.

Reto Koradi

Guest

How thick does concrete need to be to not crack?

4 inchesApplied-load cracking. In residential concrete, 4 inches is the minimum thickness for walkways and patios. Garage slabs and driveways should be 5 to 6 inches thick if any heavy truck traffic is anticipated, otherwise 4 inches is adequate.

Robin De Schepper

Guest

How thick is concrete around a pool?

6 inches thickTo be structurally sound, a concrete pool shell should generally be 6 inches thick. Depending on the engineer and the soil condition, it may be more. (On top of that, the plaster interior finish should be at least ⅜ inch thick.) The pool will also need to meet the ANSI/APSP standards.

Bithastian

Guest

How thick should a reinforced concrete driveway be?

4 inchesFor a concrete driveway to last the life of your home, it must be well constructed. Concrete driveway slabs typically are 4 inches thick but can be up to 6 inches thick to provide additional support for large trucks and other heavy vehicle traffic. Ideally, the slab has some kind of reinforcement inside.

Eugene Astafiev

Guest

How thick should concrete base be for oil tank?

Where concrete slabs are used, they should be at least 42mm* (recommended 50mm) thick.

The base should extend at least 300mm beyond the widest points of the oil tank and fully support the base of the oil tank in its entirety..

Martin Adámek

Guest

Should I seal concrete floor before painting?

Seal the concrete garage base with a pva based concrete sealing solution. This will help prevent any concrete dust contaminating the paint and also help the concrete garage floor paint to adhere to the floor. ... Most manufacturers would recommend applying the paint with a paint roller to get the best finish.

Sinh Nguyen

Guest

How many inches of concrete do I need for a garage?

fourThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix.

ianhanniballake

Guest

How much does a concrete garage floor cost UK?

The garage base calculator can calculate costs within a range of £5 – £12 per square foot of concrete laid at 4″ thick (100mm), which is typical for different areas around the UK. Please note – these are NOT quoted prices as there are many factors that can influence the cost of laying concrete, such as…

evanmcdonnal

Guest

How thick should a cement garage floor be?

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix.

PsyGik

Guest

How thick should concrete be for a garage floor?

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix.

frosty

Guest

How thick should concrete overlay be?

25 to 50 mmThe minimum recommended thickness is 1 to 2 in. (25 to 50 mm) for a fully bonded concrete overlay placed on a base slab that is practically free of cracks and in which the concrete is sound, clean, and of good quality.

Suresh Vishnoi

Guest

How thick should plaster mix be?

You should aim for a thickness of around 1–2mm.

The plaster you have mixed should last around 40 minutes before starting to set.

Alexander Bird

Guest

How thick should self-leveling concrete be?

QUIKRETE® Fast-Setting Self-Leveling Floor Resurfacer (No. 1249-51) can be installed from 1-1/2 inch (38 mm) thick to a feather edge, although a ¼ inch (6.3 mm) minimum thickness is required for heavy traffic areas.

K-ballo

Guest

How thick is a concrete driveway?

75-100mmConcrete paths should be 75-100mm thick, whereas drives, garage bases or hardstandings should be at least 100mm thick. For heavier use, such as large vans, use a 150-200mm thick concrete slab.

Onyambu

Guest

How thick should a concrete driveway be NZ?

100 mmHow thick should a concrete driveway be laid to.

A minimum of 100 mm is recommended.

Thickness is a major factor in determining the driveway's structural capacity..

abernier

Guest

How thick should a concrete garage floor be?

Standard Thickness The standard concrete garage floor is six inches thick and, with use of proper control joints, should be thick enough to withstand normal use.

Paul Sasik

Guest

How thick should a concrete shower pan be?

Thickness for Concrete Shower Pan – Base Layer The shower pan base mortar layer thickness should be approximately ½ to 1 inch thick. Since the shower floor already has a pre-slope, just apply a base mortar layer that has an even thickness throughout the shower floor area.

Nick

Guest

How thick should a concrete sunroom be?

Four inches is the minimum thickness for a concrete patio.

You'll want to make it six to eight inches thick if the patio will support a structure such as a gazebo or hot tub..

Mike

Guest

How thick should a load bearing concrete wall be?

Therefore I recommend that all the walls should be at least 9 inch thick. 4.5-inch thick walls are not structurally safe if they are beyond 7 feet in height or carry some imposed load.