Best answer

Wire mesh, like Rebar reduced the cracking and any uplift in the concrete driveway. Rebar will be used if there is a structural reason, meaning you need to carry the weight of the slab to pilings or plan to build above the slab. For a driveway, just use the wire, lap it one box around.

Answered by: oHo Date created: Jun 24, 2022

Can you hide wires in concrete wall?

Asked By: Megan Darcy Date created: Jun 11, 2022

Wire moulding, cable covers/raceway, covering the concrete with a different surface such as wood or drywall, or ghost wire are the only reasonable alternatives. Ghost wire will have limited selections for cabling (example: no power cords available with it).

Answered By: J. Abrahamson Date created: Jun 14, 2022

Do you need rubber cement when plugging a tire?

Asked By: Jan Turoň Date created: Jun 11, 2022

Some people like to add a bit more rubber cement to the plug after it is in, but it is not necessary. In fact, you can plug a tire without the rubber cement, it just makes for a quicker bond. While it is possible to put a plug into the side wall, it will generally not hold.

Answered By: kapa Date created: Jun 12, 2022

Does a concrete slab need wire mesh?

Asked By: Ken Lee Date created: Jun 20, 2022

YES When long joint spacing is required or when joints are unacceptable in floor use.

Although short joint spacings alleviate the need for reinforcement, wire mesh will allow for increased distance between joints if correctly placed in the upper portion of the slab, at least two inches below the surface..

Answered By: ittus Date created: Jun 21, 2022

Can I mix cement in a bucket?

Asked By: Sanjayrajsinh Date created: Jun 24, 2022

If you need to mix concrete by hand, there are two options: ... It has all the ingredients dry mixed together for making concrete, i.e. the cement, sand and stone. All you have to do is put it into a bucket, wheelbarrow or on a piece of plastic on the ground, add water and spend a few minutes mixing it.

Answered By: Adam Bellaire Date created: Jun 24, 2022

How do you repair a concrete balcony?

Asked By: Zohaib Ijaz Date created: Jun 14, 2022

Step by step working instructionsRemove sanding, peeling off and incompact parts of the balcony board surface by a chisel, hammer or a cutting hammer up to faultless concrete.Carefully clean the reinforcement from rust by sanding or by a wire brush or a rotation wire brush to a metallic look.More items...

Answered By: vartec Date created: Jun 15, 2022

Can I pour concrete around ABS pipe?

Asked By: I am L Date created: Jun 10, 2022

Yes, you can put concrete right over the ABS pipe. I'm sure I understand your question about the width of the 2" drain line?? You shouldn't need to wrap that pipe in anything.

Answered By: aioobe Date created: Jun 10, 2022

Can you seal concrete after pressure washing?

Asked By: Thomas Dondorf Date created: Jun 20, 2022

Once the driveway has been cleaned, you need to let any water on the concrete dry fully before the sealant is applied.

Normally, during a bright sunny day, it only takes between two and four hours for the driveway to dry.

Choose the right concrete sealer..

Answered By: Kousha Date created: Jun 23, 2022

How do you cement a rock wall?

Asked By: Cade Roux Date created: Jun 08, 2022

How to Build a Rock Wall With Cement

  1. Put the stakes in the ground at the beginning and end points of the wall, and tie the string tautly between them.
  2. Cut the chicken wire into strips the width of the trench, and lay it in the bottom of the trench.
  3. Mix some concrete in the wheelbarrow, and pour it into the trench, about 4 inches in depth.
Answered By: SYN Date created: Jun 10, 2022

Do I need to reseal my concrete driveway?

Asked By: Ashwini Chaudhary Date created: Jun 12, 2022

Sealing the driveway yearly can lead to unsightly hairline cracks and peeling. And concrete driveways should be sealed every four or five years to protect them from water penetration and to prolong their life. ... Materials to fill minor cracks in concrete come in liquids that sell for a few dollars per gallon.

Answered By: Grijesh Chauhan Date created: Jun 14, 2022

Do I need to sand concrete before painting?

Asked By: JD Isaacks Date created: Jun 13, 2022

Before you start, remove any loose or peeling paint by sanding with medium-grit sandpaper or wire-brushing the surface. If necessary, de-gloss any glossy surfaces by scuff-sanding or using a chemical deglosser. For your safety, wear protective clothing, eye goggles and acid-resistant rubber gloves and footwear.

Answered By: Tom Anderson Date created: Jun 14, 2022

Related Question Answers

Jared Wilber

Professor

Do you need rubber cement for a tire plug?

Some people like to add a bit more rubber cement to the plug after it is in, but it is not necessary. In fact, you can plug a tire without the rubber cement, it just makes for a quicker bond. While it is possible to put a plug into the side wall, it will generally not hold. Plugs are only really reliable in the tread.

Matias Elorriaga

Professor

Do you need to seal a cement driveway?

Sealing the driveway yearly can lead to unsightly hairline cracks and peeling. And concrete driveways should be sealed every four or five years to protect them from water penetration and to prolong their life.

Danny '365CSI' Engelman

Professor

Do you need to seal a concrete driveway?

Sealing the driveway yearly can lead to unsightly hairline cracks and peeling. And concrete driveways should be sealed every four or five years to protect them from water penetration and to prolong their life.

jdhao

Professor

Does 4 inch concrete need rebar?

No, depending on your proposed loads. But a 4″ thick slab really shouldn't have rebar in it, too thin. Most thing slabs, like driveways or sidewalks have a wire mesh reinforcement in them not rebar. ... If your slab is going to be subjected to enough load to need rebar it will also need to be thicker; 6″ or 8″.

Frodnar

Professor

Does a concrete driveway need rebar?

Concrete roadways, platforms, and structures typically require some type of reinforcement to help reduce cracking and prevent architectural failure. Most often, rebar (steel bars) are embedded into the concrete before it hardens. However, galvanized panels of welded wire mesh can be used as an alternative to rebar.

Dean J

Professional

Does cement board need to be sealed?

While you don't always need to seal backer board, it sometimes make sense to do so. If you are installing backer board in an area that will be subject to a great amount of moisture, like in a shower, then it makes sense to put a waterproofing sealer on it.

James Lawruk

Professional

How can I strengthen concrete without rebar?

If you're not doing a commercial-level project but still want some additional reinforcement for your concrete, a wire mesh is a great (and cheaper) alternative to rebar. Wire mesh use is becoming much more common for projects like a home driveway.

Kamil Kiełczewski

Professional

Do I need a permit to pour concrete in my back yard NYC?

In general, if you are doing any work which is going to modify your floor plan, then, you do need a permit. If you are going to pour concrete for a patio in your backyard, then, yes, you do need a permit.

Nebulastic

User

How do you clean concrete with muriatic acid?

Add cool water to your container and then, wearing full protective gear, slowly pour in the muriatic acid. Use a sprayer to soak the spots which need cleaning. Stubborn stains might also need to be scrubbed with a stiff, wire-bristled brush.

Alex. S.

User

Do I need to remove paint from concrete before repainting?

Doing the prep work before you repaint a concrete floor avoids a peeling paint job later. Concrete paint can be purchased in either latex or oil-based epoxy enamel. ... Remove all flaking, peeling paint using a scraper and wire brush. Smooth and sand rough edges using 100-grit sandpaper.

Nacho Justicia Ramos

User

Will cement adhere to asphalt?

You can put concrete over asphalt, but make sure that the asphalt is at least 2” to 4” thick. If you plan on storing many heavy vehicles on the driveway, you need 4”-6” asphalt because you need more concrete to support the weight of the vehicles.

pc_coder

User

Do I need cement board for kitchen backsplash?

But for a tile backsplash, if your wall is good and plumb, without any major ridges or problems, you don't always need to use a backer board, often you can just apply thinset to the walls and put your tiles in place.

Carlos Cordoba

Guest

How do you prepare concrete for caulking?

A wire brush works well to remove contaminants, and a drill-mounted wire wheel is often the best answer for cleaning dirty, unsound concrete. To remove some contaminants like oil or grease, it may be necessary to wipe the joint down with a solvent-laden rag, letting the solvent completely evaporate before caulking.

Justinas

Guest

How can I brighten my concrete driveway?

Chlorine Bleach This common household product is not only good in the laundry, but will brighten up and clean your concrete. Mix a solution of 1 part chlorine bleach to 1 part water. Put the mixture into a garden sprayer and spray it onto the driveway. Let it sit for 10 minutes, then scrub with a stiff scrub brush.

Shamoon

Guest

How do you clean a concrete patio without a pressure washer?

Sweep out any cracks so the dirt doesn't run down the driveway when you wash it. Spray the entire driveway with water using a garden hose sprayer. Dissolve 2 ½ ounces of washing soda in a gallon of hot water. Alternatively, sprinkle powdered dishwashing detergent over the entire driveway.

charlax

Guest

How do you remove old concrete roofing?

Roofing cement abuse is often seen on old slate and tile roofs where tar is used to stop leaks in roof valleys and in the slots between tiles and shingles. If you need to remove the tar so you can make a proper repair, use a wire brush to remove loose tar, then a razor scraper to gently remove more stubborn bits.

Frédéric Hamidi

Guest

Do I need to line a concrete planter?

Probably a layer on top of the plastic is better - it will certainly help to prevent soil clogging the drainage holes. ... Even if you do drill through the old concrete the boxes will not drain as quickly as if they are on earth. Put as many drainage holes in as you can especially if you line the sides.

Jeroen Steenbeeke

Guest

How long should you stay off a new concrete driveway?

One WeekLeave the warning tape in place to let delivery vehicles and others know that they need to stay off your concrete. After One Week – After 7 days, it's OK to drive on your new concrete with normal passenger vehicles. Avoid driving near or across the edges of the driveway, though, since those areas are still weaker.

Eric J.

Guest

What do you put under a concrete driveway?

Use wire mesh for driveways that are 4 to 5 inches thick, and rebar for those that are 5 inches or more. Place rebar in a grid pattern with a spacing between bars of approximately 12 inches. In either case, blocks should be used under the reinforcement to keep centered within the concrete.

Gabriele Petronella

Guest

Can my concrete driveway be resurfaced?

Resurfacing involves concrete driveway repair, whereby the entire thing doesn't need to come up. Instead, contractors can come in and address widespread damage by pouring a new layer of concrete over your existing driveway after removing the top layer. The result is a smooth surface that's damage-free and intact.

slamballais

Guest

Do you have to seal a concrete driveway?

And concrete driveways should be sealed every four or five years to protect them from water penetration and to prolong their life. ... Many people believe that concrete driveways don't need maintenance, so they may never apply a sealer.

Benny Neugebauer

Guest

How do you reinforce plaster molds?

Sisal fiber makes good reinforcement for plaster molds. Wire can work too, but coathanger wire will rust. Make sure you let the plaster dry for a day or two before trying to unmold it. Also, make sure you're mixing the plaster correctly.

Jason Cohen

Guest

Can you use wire mesh in concrete slab?

YES When long joint spacing is required or when joints are unacceptable in floor use. Although short joint spacings alleviate the need for reinforcement, wire mesh will allow for increased distance between joints if correctly placed in the upper portion of the slab, at least two inches below the surface.

Chris Bunch

Guest

Does a concrete patio need rebar?

Rebar is not necessary for every concrete project. ... Wire mesh use is becoming much more common for projects like a home driveway. Reinforcing concrete with rebar or wire mesh not only makes the concrete strong, but it also significantly curtails the number of cracks that appear in that concrete down the line.

BoltClock

Guest

How do you keep wire mesh on concrete slab?

Dobies/Chairs: Small concrete blocks or plastic chairs are placed between the base & the wire mesh to hold the wire mesh in the center of the slab. Both come in an assortment of sizes and ensure the wire mesh remains in the center of the slab.

Ben Reiniger

Guest

What goes under concrete driveway?

Use wire mesh for driveways that are 4 to 5 inches thick, and rebar for those that are 5 inches or more. Place rebar in a grid pattern with a spacing between bars of approximately 12 inches. In either case, blocks should be used under the reinforcement to keep centered within the concrete.

Klaus Byskov Pedersen

Guest

Do I need DPM on concrete floor?

Do I need a DPM under laminate flooring? Simply put yes. In order to prevent damp rising through the concrete floor and causing issues, a DPM should be used under all final floor types including wood flooring, laminate, vinyl and floor tiles.

Alister Bulman

Guest

Can I put concrete over asphalt?

You can put concrete over asphalt, and it is a great choice as a driveway base for residential homes. Asphalt is only suitable as a driveway base if it is at least between 2” and 4” thick for residences. ... Before you can pour concrete over asphalt, you must first soak the asphalt with water.

Sachin

Guest

Do you have to remove paint from concrete before painting?

Doing the prep work before you repaint a concrete floor avoids a peeling paint job later. Concrete paint can be purchased in either latex or oil-based epoxy enamel. ... Remove all flaking, peeling paint using a scraper and wire brush. Smooth and sand rough edges using 100-grit sandpaper.

Fredrik Hedblad

Guest

Can you pour a concrete driveway without rebar?

Rebar is not necessary for every concrete project. The general rule of thumb is that if you are pouring concrete that is more than 5 inches in depth, you are probably going to want to add in some rebar to help reinforce the entire structure. ... Wire mesh use is becoming much more common for projects like a home driveway.

Nathan H

Guest

Can you pour new concrete over old concrete driveway?

In most cases, the answer is YES! You can do that, but the existing slab must fulfill certain conditions to support a new concrete layer. Talking of concrete, who wouldn't love to see a squeaky clean patio or driveway every day?

Jeff Foster

Guest

Do I need to reinforce my concrete slab?

Concrete is an incredibly resilient material, which is why it's used so much in building and construction work. However, some types of concrete structure require reinforcements, which are often put in place as the mixture sets.

Bertrand Martel

Guest

Do you need a vapor barrier under concrete driveway?

The application of vapor barrier in exterior concrete is unnecessary due to the fact that water penetration does not matter. Any slab on grade that is enclosed and on the interior of a building should have a vapor barrier installed prior to pouring concrete, especially if flooring will be applied.

Paul Kulchenko

Guest

Do you need expansion joints in concrete driveway?

Every concrete slab, inside (basements, garages, etc.) or outside (driveways, patios, entries, etc.) are required to have joints every eight feet horizontally and vertically. Expansion Joints provide space between concrete slabs as a buffer for expansion on hot days and contraction when it is cold.

bruno077

Guest

Do you need mesh in concrete countertops?

“No material more than 3/16-inch in diameter should be used in a countertop less than 3 inches thick.” ... Ladder wire and wire mesh are used by many concrete countertop contractors, and for good reason: Both materials are strong and small enough to use effectively in countertops.

Fareed Alnamrouti

Guest

Do you need to reinforce concrete slab?

Concrete is an incredibly resilient material, which is why it's used so much in building and construction work. However, some types of concrete structure require reinforcements, which are often put in place as the mixture sets.

Torsten Marek

Guest

Do you need wire in concrete countertops?

A good rule of thumb is to use reinforcing less than 3/16 inch in diameter for concrete that will be less than 3 inches thick.

Countertops that use 3/8-inch rebar for strength can develop telegraph cracks on top of the bars.

Reinforcing wire won't cause this problem..

dfsq

Guest

Can you put cement over gravel?

Cement mix might work in some cases over an existing gravel driveway.

Laying a concrete driveway over an existing gravel one is possible, but it is not generally recommended.

...

However, if the gravel in your driveway is small enough, it is possible to create a cement driveway over the existing one..

Gert Arnold

Guest

Do you have to glue down cement board?

You cannot put a cement backer board over that. You need to put a layer or plywood, minimum 5/8 IIRC, over those boards, then mortar the backer to the plywood. Those 1x8 boards won't give a solid foundation and will flex. Over time, that will cause tile to pop loose or crack.

Michael Han_MSFT

Guest

Do I need wire mesh for concrete patio?

For a concrete patio slab the best method of providing reinforcement is to use either wire mesh or steel bars (rebar) placed in a grid pattern. The use of rebar requires that each of the intersections of rebar be tied together with rebar tie wire. ... This must be done as soon as the concrete is poured.

vitaliis

Guest

Does fiber concrete need rebar?

Sometimes you need steel fibers, and sometimes you need rebar, and only in a few limited situations can one effectively replace the other. To put it simply, steel fibers prevent cracks, while rebar limits the width of cracks. ... You can't do that with rebar. Example 2 is a concrete highway two miles long.

Nikunj Paradva

Guest

Is rebar needed in concrete driveway?

Wire mesh, like Rebar reduced the cracking and any uplift in the concrete driveway.

Rebar will be used if there is a structural reason, meaning you need to carry the weight of the slab to pilings or plan to build above the slab.

For a driveway, just use the wire, lap it one box around..

Roberto Zvjerković

Guest

Is wire mesh necessary in concrete driveway?

Using steel reinforcement will provide additional structural capacity for your driveway and is especially important if the slab will be exposed to heavy traffic. ... Use wire mesh for driveways that are 4 to 5 inches thick, and rebar for those that are 5 inches or more.

lmiguelvargasf

Guest

Will concrete crack without rebar?

Really depends on what the slab is used for but in general no you can install wire mesh or use fibered concrete. However you do need something to tie the concrete it just doesn't have to be rebar. You do not need rebar for any slab if you make it thick enough and space the joints properly. ... Any concrete slab can crack.

ProfK

Guest

Should I put a sealer on my new concrete driveway?

Experts recommend using a penetrating sealer outdoors because it sinks down into the concrete and has a more natural, matte finish. It is very important that sealers used on exterior concrete allow both air and moisture to pass through. A driveway sealer should be applied after the freshly poured concrete has cured.

luk2302

Guest

Should I put sealer on my concrete driveway?

And concrete driveways should be sealed every four or five years to protect them from water penetration and to prolong their life. Many people believe that concrete driveways don't need maintenance, so they may never apply a sealer. ... The first step in driveway maintenance is the repair of cracks and holes.

Hongbo Miao

Guest

Should I put wire mesh in concrete slab?

Wire mesh makes concrete more durable and increases its strength. The area in which the concrete will be laid down should be covered in mesh before pouring commences.