Best answer

If the slab is too thin, it may break under load and fail before its time. If the slab is too thick, it costs more than it should. Slab thickness is a major factor in the cost of a concrete floor, so there's often pressure, which can become intense, to make the slab as thin as possible.

Answered by: Roar S. Date created: Jun 27, 2022

Why is my plaster cracking as it dries?

Asked By: nicolaskruchten Date created: Jun 23, 2022

Drying shrinkage cracks are the result of moisture loss after the plaster has hardened. Plaster applied in layers that are too thick will also tend to crack in this way. These cracks are normally stable and can be filled with a proprietary filler and painted over.

Answered By: Michael Krelin - hacker Date created: Jun 26, 2022

How do you thicken plaster of Paris?

Asked By: anthony_718 Date created: Jun 19, 2022

In the end, the plaster should be thick, but not difficult to stir. If it seems too thick, add more water. If it is too runny, add more flour until it thickens. Work with the plaster within 10 minutes.

Answered By: Didier Spezia Date created: Jun 22, 2022

How thick should a concrete slab be for a mobile home?

Asked By: cmbuckley Date created: Jun 18, 2022

4 to 6 inches

Answered By: Stargateur Date created: Jun 20, 2022

Can I pour a 2 inch concrete slab?

Asked By: abatishchev Date created: Jun 13, 2022

If done properly, new concrete can often be poured right over an existing slab. For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.

Answered By: Nguyen Minh Binh Date created: Jun 14, 2022

How thick does a concrete slab need to be for a garage?

Asked By: bennygenel Date created: Jun 15, 2022

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region.

Answered By: rraphael Date created: Jun 18, 2022

What is the minimum depth for a concrete slab?

Asked By: Mate Mrše Date created: Jun 16, 2022

5 cm thickWhatever you plan on doing, your concrete slab should be at least 5 cm thick. That is the bare minimum of a concrete slab thickness. This is the thickness of the concrete slab alone and it doesn't include the gravel base, if you are using something like that.

Answered By: JamesFaix Date created: Jun 16, 2022

Why does my plaster crack when drying?

Asked By: laktak Date created: Jun 25, 2022

Drying shrinkage cracks are the result of moisture loss after the plaster has hardened. ... Plaster applied in layers that are too thick will also tend to crack in this way. These cracks are normally stable and can be filled with a proprietary filler and painted over.

Answered By: Grzegorz Żur Date created: Jun 26, 2022

How thick should a concrete slab be for a shed?

Asked By: Aprillion Date created: Jun 22, 2022

Recommended Thickness of Concrete Slabs Shed Slabs: 3 1/2 inches thick. Shed floors that are being used for studio sheds or workshops will use a 3 1/2" thickness. Driveways: 4 inches, some areas require 5 inches. Many garage sheds need a driveway approaching the large shed door.

Answered By: Stein Åsmul Date created: Jun 23, 2022

How thin can you pour concrete over concrete?

Asked By: pmg Date created: Jun 21, 2022

2 inchesIf done properly, new concrete can often be poured right over an existing slab. For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.

Answered By: Andrew Date created: Jun 22, 2022

Can I mix cement in a 5 gallon bucket?

Asked By: Pᴇʜ Date created: Jun 20, 2022

It can be mixed in a 5 gallon bucket, a wash tub, or on a plastic sheet or a tarp. When you're getting your hands in the mix like this, be sure to wear thick gloves. Concrete is caustic and thinner gloves will rip too easily.

Answered By: Christian Oudard Date created: Jun 22, 2022

Related Question Answers

Chandan Nayak

Professor

How thick is a suspended concrete slab?

around 200mmA suspended slab is raised off the ground and has an accessible sub-floor area. In a residential situation, the slab is around 200mm thick and is supported by external sub-floor walls of brick or concrete block etc. The slab is also supported by free-standing brick or concrete piers.

Delan Azabani

Professor

Can I pour new concrete over old?

If done properly, new concrete can often be poured right over an existing slab. For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.

GURU Shreyansh

Professor

Why did my concrete sealer turned white?

A white or cloudy color is caused by moisture that is trapped inside the sealer. ... However, if it's too hot and too humid, then also it's possible the sealer surface could dry faster than the moisture can escape. The sealer was applied too thick. It's important to apply concrete sealers in thin and even coats.

Guss

Professor

How much would a 40x60 concrete slab cost?

How much does a 40×60 concrete slab cost? It would be about $8,500 to $12,000 for a 40×60 foot concrete slab, 6 inches thick. That's based on national averages of around $5 per square foot for a fully engineered, finished concrete slab, including labor and materials.

Frank Farmer

Professional

Do you need a footer for a concrete slab?

All 3 types of slabs will need a footer and a slab of at least 4″ thick. The footers depth needs to be the depth of the frost line or as per local code, but no less than 12″ deep. ... Slab Foundations Like all foundations, the slab starts with concrete footers poured 24 inches below projected finish grade.

joran

Professional

Can concrete be too strong?

The paper, “202 Observations On Concrete That Is Too-Quickly-Strong,” cites cases where concrete cracked because it was too strong from too much cement and 66 investigations that related durability problems to cement hydrating too rapidly because of high values of fineness, C3S, C3A, and/or alkalies.

BeeOnRope

Professional

Can I build a garage on a concrete slab?

You may want to consider a 6" thick slab for larger vehicles such as trucks or RVs. For a garage WITHOUT a floor - BUILT ON SITE: Prepare a level concrete slab at least 4” thick and to the exact, outside, dimensions of your garage. You may want to consider a 6" thick slab for larger vehicles such as trucks or RVs.

Pentium10

Professional

Can I pour concrete over existing concrete?

If done properly, new concrete can often be poured right over an existing slab. ... For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.

Valentin C

Professional

Can you pour concrete 2 inches thick?

A: Concrete is typically applied at a thickness of 2 inches or more, but the thicker it is, the stronger the slab will be. Four inches is most common for a slab. ... Products labeled “High Strength Concrete Mix” are ideal for these types of applications.

Kemp

User

Does 4 inch concrete need rebar?

No, depending on your proposed loads. But a 4″ thick slab really shouldn't have rebar in it, too thin. Most thing slabs, like driveways or sidewalks have a wire mesh reinforcement in them not rebar. ... If your slab is going to be subjected to enough load to need rebar it will also need to be thicker; 6″ or 8″.

Chris Hayes

User

Can you float concrete the next day?

Step 5 - Wait for Surface to Dry Wait for the water to completely drain back in before working any further on the slab. If you begin using a float too soon, you could sweep some of the water off the slab before it has a chance to be re-absorbed. Reducing the water content will weaken the surface of the concrete.

Jay

User

How thick is a concrete basketball court?

You need: A slab at least 4 inches thick, with material at least 3,000-3,500 pounds per square inch (PSI) Rebar 1/2 inch thick to support the concrete..

Juan Antonio Gomez Moriano

User

How thick should a concrete slab be for a basketball court?

3500 PSIBase Material Many basketball courts are built over a 4” thick concrete slab using 3500 PSI concrete and 1/2″ rebar reinforcements. Concrete is considered ideal for basketball courts as a permanent structure that when done right will not require any maintenance.

Grant Miller

User

How thick does the concrete need to be for a car lift?

100mmThe minimum and recommended thicknesses of concrete slab for car hoists. Garage Equipment's two and four post hoists require a minimum of 100mm (about 4”) of reinforced concrete slab to be safely installed.

nulltoken

Guest

How thick of a concrete slab for a hot tub?

about 4 inchesConcrete Slab The base of reinforced concrete should be about 4 inches thick and be able to withstand a weight of at least 115 pounds per square foot, especially for larger spas. The concrete should be fully cured prior to placing the tub.

Gass

Guest

Can you pour concrete 1 inch thick?

There aren't many reasons to have only a 1-inch thick concrete surface.

It is too thin to use as a flooring just by itself; however if you need to resurface damaged concrete, a 1-inch layer is a good amount.

The old surface is prepared so that the new concrete will adhere, then the new cement is added..

Pablo Fernandez

Guest

How do you break up a thick concrete slab?

Start to break the concrete, starting six inches from the edge and working your way in. For slabs less than four inches thick, use a sledgehammer. For more than four inches thick, use a demolition hammer.

Dávid Pásztor

Guest

How thick should a concrete slab be for a pole barn?

4”Thickness – The industry standard for a residential pole barn, where you are storing lawn mowers, toys, or regular vehicles, is reinforced concrete floor that is 4” thick. If you have heavier equipment, you may want to consider flooring up to 6” thick for better wear and tear.

HaaLeo

Guest

How thick should concrete resurfacer be?

1/2 inchUnlike other cement products, it is designed to be applied in very thin coats (no more than 1/2 inch thick), and its additives provide good adhesion to an existing slab. Concrete resurfacer is a very strong product, rated for a compressive strength of about 4,500 psi.

WouterD

Guest

How do you cut concrete expansion joints?

The thumb rule used to determine the depth of the control joint is to cut the joints one-quarter to one-third the slab thickness. If the concrete slab laid is 150mm thick, the depth of the joint must be 40mm to 50mm. If the joint is too deep, aggregate interlocking will not be sufficient to transfer loads.

Valentin Despa

Guest

How much does it cost to cement a pole barn?

It would be about $8,500 to $12,000 for a 40×60 foot concrete slab, 6 inches thick. That's based on national averages of around $5 per square foot for a fully engineered, finished concrete slab, including labor and materials.

Psidom

Guest

How thick does a concrete slab for a shed need to be?

4-inchA 4-inch slab is generally a good thickness for a typical shed. This concrete floor can be poured in most locales on a 4-inch base of compacted gravel. That requires an excavation of at least 6 inches to make a slab that will be 2 inches above the surrounding ground.

Zim

Guest

How thick does a concrete slab need to be?

six (6) inchesIt is essential that you keep your concrete slab at no more than six (6) inches of thickness. Also, it would be best to work the numbers out if you wish to work with any lesser as you can only put in one slab.

dev

Guest

How thick does concrete need to be for a shed?

A 4-inch slab is generally a good thickness for a typical shed.

This concrete floor can be poured in most locales on a 4-inch base of compacted gravel.

That requires an excavation of at least 6 inches to make a slab that will be 2 inches above the surrounding ground..

Dean Harding

Guest

Can a concrete slab be poured in sections?

Pour the concrete in small sections Don't fill the whole form or giant sections because the mound of extra concrete you'll drag back with the screed board will get too heavy.

Vineet Reynolds

Guest

Can I pour concrete 3 inches thick?

Here, pouring a concrete slab 4 inches in thickness is fine. ... A 3- to 4-inch slab will work for the floor of a storage or tool shed, workshop, garden shed, or playhouse. Steps to pouring a concrete slab. 1.

PineCoders-LucF

Guest

Can you use concrete as a base for pavers?

Mortar or Concrete Mix A 4- to 6-inch-thick concrete slab is suitable as a base for pavers, which can be laid directly onto the wet concrete so they are held in place when it dries.

Andrew

Guest

Does a garage concrete slab need footings?

All three types of slabs will need a footer and a slab of at least 4″ thick. The footer's depth needs to be the frost line's depth or as per local code, but no less than 12″ deep. The width of the footer needs to be at least 12″ wide.

Chris de Vries

Guest

How thick can you pour concrete resurfacer?

1/2 inchUnlike other cement products, it is designed to be applied in very thin coats (no more than 1/2 inch thick), and its additives provide good adhesion to an existing slab. Concrete resurfacer is a very strong product, rated for a compressive strength of about 4,500 psi.

Jiew Meng

Guest

Can I put cement between pavers?

Mortar or Concrete Mix A 4- to 6-inch-thick concrete slab is suitable as a base for pavers, which can be laid directly onto the wet concrete so they are held in place when it dries.

...

Mortar also can be used in the joints between pavers, just like grout is used between tiles..

rogerdpack

Guest

Can you put concrete between pavers?

Mortar or Concrete Mix A 4- to 6-inch-thick concrete slab is suitable as a base for pavers, which can be laid directly onto the wet concrete so they are held in place when it dries. ... Mortar also can be used in the joints between pavers, just like grout is used between tiles.

peak

Guest

How do you lay concrete over a concrete slab?

If done properly, new concrete can often be poured right over an existing slab.

For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete..

sakra

Guest

How thick should a reinforced concrete driveway be?

4 inchesFor a concrete driveway to last the life of your home, it must be well constructed. Concrete driveway slabs typically are 4 inches thick but can be up to 6 inches thick to provide additional support for large trucks and other heavy vehicle traffic. Ideally, the slab has some kind of reinforcement inside.

kohske

Guest

Will concrete crack without rebar?

Really depends on what the slab is used for but in general no you can install wire mesh or use fibered concrete. However you do need something to tie the concrete it just doesn't have to be rebar. You do not need rebar for any slab if you make it thick enough and space the joints properly. ... Any concrete slab can crack.

Francisco Puga

Guest

Can I pour concrete 1 inch thick?

There aren't many reasons to have only a 1-inch thick concrete surface. It is too thin to use as a flooring just by itself; however if you need to resurface damaged concrete, a 1-inch layer is a good amount. The old surface is prepared so that the new concrete will adhere, then the new cement is added.

Marcin Nabiałek

Guest

Should I seal my new concrete garage floor?

Sealing products can not be used on newly poured concrete. Homeowners would have to wait 28 to 30 days when the concrete has completely cured. Applying the sealer too early will be detrimental to the durability of the new concrete slab.

Chandu

Guest

How thick does a concrete slab need to be for a shop?

If these steps are performed correctly, the owner can expect an attractive, durable product. Standard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks.

Jon Cage

Guest

How thick should a cement garage floor be?

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix.

Paul Sasik

Guest

How thick should concrete be for a garage floor?

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix.

canon

Guest

How thin can concrete be poured?

1-inchThere aren't many reasons to have only a 1-inch thick concrete surface. It is too thin to use as a flooring just by itself; however if you need to resurface damaged concrete, a 1-inch layer is a good amount. The old surface is prepared so that the new concrete will adhere, then the new cement is added.

Stuart Marks

Guest

How thin can concrete overlay be?

Concrete overlays less than 6 inches (152 mm) thick are commonly identified as “thin” concrete overlays, while the term “ultra thin” is sometimes used to refer to overlays less than 4 inches (102 mm) thick. These thin overlays also feature smaller slab sizes, with 6 ft by 6 ft (1.8 by 1.8 m) panels commonly used.

Daniel C. Sobral

Guest

How thin can you lay sand and cement screed?

Traditional cement sand screeds This is more likely to happen if the screed is too thin. Bonded screeds should therefore be thin, normally less than 50mm. Unbonded screeds should be thick, normally 70mm or more, and 100mm or more if curling must be avoided.

Jonik

Guest

What happens if concrete dries too quickly?

If water evaporates too quickly the concrete's strength can be compromised and you may end up with cracks. ... It is also important to note that too much water in the mixture to begin with can cause problems with the drying process. Too much water can result in shrinkage and reduce the strength of the concrete.

OMR

Guest

What happens if plaster is too thick?

Nothing will happen, it will be too hard to finish off the white set plaster if it is too thick. ... Would plastering over a dent in a wall and providing three extra coats of primer or paint to it fix it so it's not noticeable anymore?

Shashank Vivek

Guest

Why is my concrete sealer not drying?

The sealer was not completely dry when an additional coat was applied. ... However, if it's too hot and too humid, then also it's possible the sealer surface could dry faster than the moisture can escape. The sealer was applied too thick. It's important to apply concrete sealers in thin and even coats.