How much concrete do I need to fill a hole?

Each hole for the terminal posts must be 8 inches in diameter and 30 inches deep, requiring 0.85 cubic feet of concrete to fill.

Each hole is 2'x2'x2' which equals 8 cubic feet. You have 2 of these so you need 16 cubic feet of concrete. An 80 lb (36.3 kg) bag of Quikrete yields approximately 0.60 cu ft (17 L). 16 cubic feet / 0.6 cubic feet / per bag = 27 (80#) bags of concrete mix.

If you're not sure what size hole to dig, a rule of thumb is to use a hole diameter 3 times the post diameter and 1⁄3 as deep as the post height. See below for more information. Average is $115 per yd3, although your price will vary based on the type of concrete, vendor, and location.

To core fill 200mm blocks allow 0.8m3 of concrete per 100 blocks.

To core fill 200mm 'H' blocks allow 0.84m3 of concrete per 100 blocks.

To core fill 300mm blocks allow 1.1m3 of concrete per 100 blocks.

To core fill 300mm 'H' blocks allow 1.32m3 of concrete per 100 blocks..

With a brief look, a 20x20 area at 6 inches deep, you would need approximately 10.52 tons or 7.41 cubic yards of gravel. Concrete reinforcing is also recommended in high traffic areas and medium to large areas.

To plaster over small holes, first scrape off any old loose plaster with the edge of a scraper or filling knife. Then use a damp paintbrush to wet the hole. This nifty trick helps the filler bond to the surface. Now squeeze some plaster directly into the hole or on to your filling knife.

Set the spray nozzle to its highest pressure. Mix together in a bucket one part Portland cement, three parts sand and enough water to make a stiff patching compound. Fill the hole with the patching compound. Use the corner of a trowel or your finger to pack the compound into the hole, making sure it is completely full.

1. Repair the hole in the wall with plaster. Use the handle of your putty knife to tap the edges of your hole down.
2. Apply a second coat of plaster to the hole in the wall. Once the first coat of plaster is dry, give it a light hand sand and dust the surface clean with a rag.

How to: Make a Drainage Hole in a Concrete Planter. But to keep that succulent alive, it needs a bed or rocks at the bottom and ideally a drainage hole for excess water. Having a drainage hole is ideal for any type of potted plant, especially houseplants.

Consider Adding Posts to Concrete From here, you should fill the hole with about 6 inches of gravel. This will prevent rotting by ensuring that the post is kept dry when water makes its way into the soil. Place the post in the gravel, then fill with a batch of cement until it reaches the top of the hole.

Steps

• Measure and outline the space for your wall.
• Dig out the soil to form space for the wall and footer.
• Compact and level out the soil with a tamper tool.
• Pour 6 in (15 cm) of gravel into the hole.
• Place a layer of steel rebar ⅓ of the way up the hole.
• Mix and pour concrete to fill the footer hole.

Put the post into the hole, level the post and fill the hole with QUIKRETE Fast Setting Concrete Mix within three to four inches from the top of the hole. Pour up to one gallon of water into the hole until is soaks into the QUIKRETE Fast Setting Concrete Mix and allow the concrete to set for 20 to 40 minutes.

elevenThe recommended hole size is 16 inches in diameter and 48 inches deep. You will need eleven 80-lb bags of concrete for the installation. How much does it cost to install an in ground basketball hoop? On average, installation will cost around $450.00 for an in-ground system if you have it professionally installed.

12,000 pound two-post lifts (and higher capacity): Six (6) inches of concrete at 3000 PSI is required.

I used three 80 pound bags of concrete mix to fill all of the 48" length of this 8" diameter tube form and had some concrete left over.

Beside above, how much crushed concrete do I need calculator? In the construction world, most materials are measured in cubic yards. Multiply the length (L), in feet, by the width (W), in feet, by the height (H), in feet, and divide by 27. This will tell you how many cubic yards of crushed stone you need.

Calculate the volume of the hole in cubic metres (using V = πr2h) and then subtract the volume of your post. This will give you the volume of concrete required. Simply multiply the volume figure by 108 (108 bags per cubic metre) to give the amount of 20kg bags needed to fill the void.

How to re-pour concrete in saw-cut slab? hammer-drill holes sideways into the cut surfaces of the concrete to make holes 3-inch deep for dowels (3/8 rebar that I already have sitting around) remove all loose material from the dirt hole. clean rocks and concrete out of the fill dirt.More items...•Jan 12, 2007

Pour the dry concrete straight into the hole leaving 3 to 4 inches of space from the top of the hole. In most cases a 50-pound bag of quick-dry concrete should suffice.

To calculate how much concrete you need, you need to know the post size you are going to use and how many posts you are installing.

Your post diameter and height determine how big each hole needs to be.

As stated above, fence post holes should be 3 times the diameter of your post and 1⁄3 as deep as your post..

As to how many bags....a 55 gallon drum filled clear to the top is actually closer to 60 gallons. And 60 gallons is 8 cu ft. So if you buy 60lb bags, those do 1/2 cu ft each so you would need 16 of them. IF you buy 80lb bags (2/3 cu ft) you would need 12 bags.

For example, a sono tube with a 10" diameter and a 4' depth requires 0.08 cubic yards of concrete.

The general rule of thumb when setting a post is that the depth of the post's hole needs to be 1/3 to 1/2 of the actual above-ground height of the post. So, six-foot-high fence posts ideally need to be buried three feet into the ground. The diameter of your post hole should be three times the diameter of your post.

For example, a sono tube with a 10" diameter and a 4' depth requires 0.08 cubic yards of concrete..

The depth of the hole should be 1/3-1/4 the post height above ground (i.e., a 6-foot tall would require a hole depth of at least 2 feet).

Most fence post holes will need between 1 - 4 bags of concrete to securely hold the post in place.

The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post.

Depth of the hole is one-third to half the above ground height of the fence post..

Plan on at least 5 minutes per cubic yard, for unloading time. How much concrete do I need? Order this much concrete, for these standard pool sizes. 12 x 24 – 5 yards, 14 x 28 – 6 yards, 16 x 32 – 7 yards, 18 x 36 – 8 yards and a 20 x 40 – 9 yards.

Calculate Concrete Volume With the volume of the submerged post and the volume of the hole figured out, subtract the post volume from the hole volume, and you will have the volume of concrete needed for each hole.

Simply multiply that amount times the number of posts to get a total quantity..

Remember, the depth of the post hole should be one-half of the above-ground post height.

(Example: For a 6 feet above ground post, use a post with an overall height of 9 feet and place 3 feet in the ground).

The calculator will indicate the number of 50 lb.

bags of QUIKRETE® Fast-Setting Concrete you need..

The general rule of thumb when setting a post is that the depth of the post's hole needs to be 1/3 to 1/2 of the actual above-ground height of the post. So, six-foot-high fence posts ideally need to be buried three feet into the ground.

An ideal patch to use for both purposes is hydraulic cement, which expands to fill cracks and holes as it dries.

Remove loose material from the hole in the wall by probing it with the tip of a screwdriver or blade of a putty knife.

Clean the hole and surrounding area with a wire brush..

Once you know how big the room is and ideally know how many square meters are in it, you can simply divide that figure by 9 to give you about how many bags of multi finish plaster you will need. Multi finish covers 10m2, but I say 9m2 to all allow for wastage.

1 - 4 bagsMost fence post holes will need between 1 - 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.

To begin reinforcing the post, dig a few inches of soil away from it around the perimeter. Fill the hole with approximately 6 inches of gravel. Top the gravel with rapid-set cement mix powder to fill the hole to 3 inches below the surface of the soil.

A hole that's 2 feet long, 2 feet wide and 2 feet deep is 8 cubic feet. Multiply the cubic feet by . 45, if you're using 60-pound bags of concrete, or by . 6, if you're using 80-pound bags.

To calculate how much concrete you need, you need to know the post size you are going to use and how many posts you are installing. Your post diameter and height determine how big each hole needs to be. As stated above, fence post holes should be 3 times the diameter of your post and 1⁄3 as deep as your post.

Each 80 lb (36.3 kg) bag of QUIKRETE® grout will fill the cores of approximately 3 standard 8" × 8" × 16" (203 × 203 × 406 mm) block.

To calculate how much concrete you need, you need to know the post size you are going to use and how many posts you are installing. Your post diameter and height determine how big each hole needs to be. As stated above, fence post holes should be 3 times the diameter of your post and 1⁄3 as deep as your post.

Set the post into the hole and attach 2x4 braces to adjacent sides of the post. Use a level to position the post perfectly vertical. Fill the hole with Fast-Setting Concrete up to 3 to 4 inches below ground level. Pour about a gallon of water per 50 lb bag into the hole and allow the water to saturate the concrete mix.

Concrete Slab Prices By SizeSlab SizeSquare FeetAverage Cost Installed15x15225$1,38820x20400$2,46824x24576$3,55420x30600$3,7026 more rows

A five gallon bucket can hold . 45 cubic feet of concrete when mixed with water. In other words, one 60 pound bag of pre-mix or an equivalent Portland Cement/rock and sand mix.

Apply the Sealant Depending on how porous your concrete is, a gallon of sealer will cover 250 to 500 square feet.

They are 4 feet in height and 10 inches in width (diameter), or 4′ x 10″.Choose Round Column (or Round Slab) on the calculator.Enter Height 4 ft (or 48 in)Enter Diameter 10 in.Calculate and the answer is 0.08 cubic yards for one concrete tube.Multiply 0.08 x 50 = 4 total cubic yards of concrete for 50 tubes.More items...

Dry Method Instructions:Prepare and wet the hole. Before you begin, you need to dig and prepare the hole. ... Place post into the hole. Place the post into the hole. ... Place concrete into the hole. ... Pour water on top. ... Tamp the mix. ... Mix concrete with water. ... Place mixture into the hole.Aug 19, 2019

Fill the first three inches up with gravel so the end of the post doesn't come into contact with the dirt. Gravel allows water to drain quickly away from the post and into the soil. Be sure to place the post in the center of the hole. Finally, fill the entire hole up with cement to the top.

For example, a sono tube with a 10" diameter and a 4' depth requires 0.08 cubic yards of concrete.

You can also use concrete block to build your own piers, but this requires that you pour a concrete footing at the bottom of the hole for the block to rest on. You then have to fill the cores of the concrete block with steel rods and a concrete mix to make them solid.

Concrete screws provide a quick, easy and incredibly strong way to fasten to concrete. And best of all, there's no hammering required or anchor or shield to install. All you do is drill a hole and drive in the screw.

Each diameter of concrete screw has a specific diameter carbide drill bit that must be used for installation. The 3/16” diameter screw requires a 5/32” hole and the 1/4” requires a 3/16” hole. The hole must be drilled using a hammer drill with a carbide tipped bit meeting ANSI standards.

Manufacturers unanimously require vinyl fence posts to be installed into a concrete filled post hole. Setting vinyl posts into concrete provides a consistent footing to ensure the posts will remain inline and true for years to come. Concrete should fill the post hole up to 3-4 inches from the top.