Best answer

Squirt some dish soap onto the oil stain. Scrub the stain with a heavy-duty brush. Then rinse away the soap with water. Repeat the process until the oil stain fades.

Answered by: shadowsheep Date created: Jun 27, 2022

How do you remove plaster from Brick?

Asked By: F_SO_K Date created: Jun 20, 2022

Use a wide bricklayer's chisel and a masonry hammer to chip away plaster from the brick, working your way from the bottom of the wall to the top. A hydrochloric acid solution applied with a wire brush can be used to remove excess plaster residue and clean the surface to expose the beauty of the brick.

Answered By: Aquarius_Girl Date created: Jun 23, 2022

How do you remove acrylic paint from plaster walls?

Asked By: AlikElzin-kilaka Date created: Jun 23, 2022

The easiest way to remove old paint, if it is already loosened, peeling or chipped, is with a putty knife, plastic scraper or an oscillating tool with rigid scraper blade. Simply work the flat edge of the tool across the surface of the wall to remove loosened pieces of paint.

Answered By: Grant Miller Date created: Jun 23, 2022

Can an old concrete driveway be sealed?

Asked By: dww Date created: Jun 25, 2022

A: Yes! Old concrete can be sealed for the first time or resealed if it has been previously sealed with a concrete sealer. ... You want to make sure all mold, mildew, efflorescence, rust, grease and oil are removed from the concrete before sealing as you do not want to seal these elements into the concrete.

Answered By: Alexander O'Mara Date created: Jun 26, 2022

Can you apply concrete stain over sealer?

Asked By: Wais Kamal Date created: Jun 16, 2022

You cannot acid stain concrete that has an acrylic sealer or any other type of sealer. Remove the sealer with a solvent before attempting to stain the surface. Use a caustic concrete stripper to remove all of the dirt, oil and acrylic residue before attempting to stain the concrete.

Answered By: Doug Stevenson Date created: Jun 17, 2022

How do I whiten my concrete driveway?

Asked By: CL. Date created: Jun 21, 2022

Bleach, Soap, and Water Mixture Mix one cup of bleach with one cup of powdered laundry detergent, then add 15 cups of hot water. Pour your mixture over your driveway's dirty areas, such as the parts that contain oil stains. Work your mixture in using a bristle brush and scrub for approximately 20 minutes.

Answered By: Cesar Canassa Date created: Jun 22, 2022

How do you clean concrete resin?

Asked By: Eran Date created: Jun 14, 2022

Use pH-neutral cleaners.

Give the solution time to loosen dirt and debris, but don't let it dry.

Rinse well to keep the solution from building up and over time creating a slippery surface.

Immediately remove oil and grease with a water-based solution of alkaline detergent..

Answered By: joran Date created: Jun 15, 2022

How do you fix a broken concrete driveway?

Asked By: rcs Date created: Jun 09, 2022

Repair large driveway cracks and potholes by removing stones, dirt, grit, dust and crumbled concrete from the area to be patched. Brush the area with plain water to dampen it. Paint the area to be patched with the acrylic bonding agent. Work the bonder into the cracked area with the paintbrush.

Answered By: Nick Stinemates Date created: Jun 10, 2022

Do I need to seal my concrete garage floor?

Asked By: Pebbl Date created: Jun 12, 2022

Because garage floors are protected from outdoor elements, they don't generally need sealed as often as a concrete driveway. However, most garage floors are made from concrete, making them susceptible to cracking and moisture intrusion from oil spills, antifreeze leakage, and other household chemicals.

Answered By: Derick Date created: Jun 14, 2022

Do you need to seal a cement driveway?

Asked By: Elton Stoneman Date created: Jun 23, 2022

Sealing the driveway yearly can lead to unsightly hairline cracks and peeling. And concrete driveways should be sealed every four or five years to protect them from water penetration and to prolong their life.

Answered By: Yevhen Laichenkov Date created: Jun 26, 2022

Do you need to seal a concrete driveway?

Asked By: mu is too short Date created: Jun 19, 2022

Sealing the driveway yearly can lead to unsightly hairline cracks and peeling. And concrete driveways should be sealed every four or five years to protect them from water penetration and to prolong their life.

Answered By: John Date created: Jun 19, 2022

Related Question Answers

Georg Fritzsche

Professor

How do you knock off plaster walls?

You can remove plaster from walls using a hammer and bolster chisel but it is time consuming, in some cases where the plaster has blown completely you can remove it using a spade. Before attempting to remove the plaster it is a good idea to close the door to the room and seal it completely, perhaps using a zip door.

quantumSoup

Professor

How do you make a concrete mold release agent?

Coat the mold with a release agent to prevent concrete from sticking. You can purchase a release agent made specifically for concrete molds, or make your own by mixing 1 part castor oil with 8 parts denatured alcohol. Shake the mixture well before spraying the mold.

Benjamin Pasero

Professor

How do you make a concrete release agent?

Make your own satisfactory substitution.Purchase two common oils, such as vegetable oil and mineral oil, that are free of paraffin and other kinds of waxes. ... Apply the oil to the concrete forms with a paintbrush. ... Pour the concrete into the form as directed for your project.

DaveShaw

Professor

How do you make stamped concrete look new?

Wash the stamped concrete with our SealGreen Oil Cleaner Degreaser - https://sealgreen.com/oil-cleaner-degreaser-concentrate/ , allow to dry then apply color stain from our color chart - https://sealgreen.com/color-stains/ , allow to dry for at least 24 hours, and seal twice with SealGreen E15 Epoxy Stamped Concrete ...

Doug Sillars

Professor

How do you prepare concrete for sealing?

Here's a step-by-step summary of how to seal concrete:Remove all oil, grease, stains, dirt, and dust from the concrete.Strip any existing sealer from the surface.Open up the concrete with an etching solution.Apply a thin coat of sealer using a roller or sprayer.Wait for the first layer of sealer to dry.More items...

PSL

Professional

How do you keep cement from sticking to molds?

You can purchase a release agent made specifically for concrete molds, or make your own by mixing 1 part castor oil with 8 parts denatured alcohol. Shake the mixture well before spraying the mold.

Martin Löper

Professional

How do you clean a concrete tennis court?

High pressure cleaning is the fastest and safest way to clean the tennis court. To avoid algae and other fungal contaminants growing on the court we recommend you purchase a commercial 'leaf blower' to remove any debris from the tennis court. You should attempt to remove debris at least once or twice a week.

Steve Jessop

Professional

How do you remove water-based concrete sealer?

How to remove a water-based concrete sealer:Use a product such as Aqua Mix's Sealer and Coating Remover.You can also try acid etching the concrete (followed by neutralizing)You can mechanically scarify the concrete to remove the previous sealer.May 14, 2014

JosephStyons

Professional

How do you repair concrete pool tile?

Remove all loose tiles. Remove all loose cement from behind the tiles. Use hydraulic cement to fix cracks & holes. Let dry for 24 hours.

Mostafa

User

How do you treat concrete forms?

Some users prefer to coat the rubber with a thin film of castor oil or other vegetable oil, lanolin, or water emulsion wax. Paraffin oil generally is lightly sprayed over plastic foam forms or form liners. Castor oil, or petroleum jelly thinned with kerosene, also are good release agents.

Carlos Cordoba

User

What can you put on wood to keep concrete from sticking?

Any type of oil will prevent concrete from sticking to wood. Spray the surfaces that will face the wet concrete with a heavy saturation of oil. Allow the oil to penetrate the wood for 15 to 20 minutes. Apply a second heavy spraying of oil just before pouring concrete.

Ates Goral

User

What kind of oil do you use for concrete forms?

SUNOCO CONCRETE FORM RELEASE OIL is a premium quality lubricant formulated as a quick, non-staining releasing agent for metal and wooden forms. The fluid is specially compounded with a combination spreading and releasing agent to prevent cement from adhering to form surfaces.

vks

User

How do you get concrete to stick to wood?

Oil-Based Release Agents.

At one time, construction professionals would create their own oil-based form release agents using materials such as diesel fuel, home heating oil and mineral oil to keep poured concrete from sticking to wood..

jezrael

User

Do I need to remove paint from concrete before repainting?

Doing the prep work before you repaint a concrete floor avoids a peeling paint job later. Concrete paint can be purchased in either latex or oil-based epoxy enamel. ... Remove all flaking, peeling paint using a scraper and wire brush. Smooth and sand rough edges using 100-grit sandpaper.

Federico klez Culloca

Guest

How do you prepare concrete for caulking?

A wire brush works well to remove contaminants, and a drill-mounted wire wheel is often the best answer for cleaning dirty, unsound concrete. To remove some contaminants like oil or grease, it may be necessary to wipe the joint down with a solvent-laden rag, letting the solvent completely evaporate before caulking.

RomainValeri

Guest

How do you remove old cement from tiles?

How to remove cement stains from tilesSoak. Soak a cloth well with white vinegar.Apply. Place the cloth over the stain.Let it sit. Let the cloth soak the stain well, leaving it on for 2 hours.Reapply. If the vinegar keeps evaporating, reapply it periodically to keep the area wet.Scrub. ... Repeat. ... Rinse. ... Wash.More items...•Apr 10, 2020

Gareth Latty

Guest

What removes oil stains from concrete driveway?

The four best ways to remove oil stains from concrete are:Wash away the oil with a strong detergent, and a scrub brush or sponge.Use a concrete cleaner or degreaser to loosen and remove the oil.Apply a poultice that will break down the oil and suck it from the concrete.More items....

Pavel Minaev

Guest

Can you paint a concrete driveway?

To properly paint a concrete driveway, you must first ensure that it is completely cleared and clean.

Next, fill any cracks, if applicable, so you can paint over them and give the driveway a nice even coat.

...

Avoid painting an asphalt driveway as the paint will chip and peel much more easily since asphalt is oil-based..

abccd

Guest

Should I seal concrete joints?

Stopping water from flowing under your concrete is probably the most important thing you can do to keep your driveway from sinking and becoming out of level. Caulking the joints and cracks is the best way to stop this from happening. Even expansion joints in your concrete driveway should be caulked.

Daniel Gratzer

Guest

How do you keep cement plaster from cracking?

How to Prevent Plaster Defects in Construction Phase?The use of well-graded sand can prevent the development of crazing cracks. ... Remove wall surface from loose material and clean it from dust and oil to avoid plaster debonding.More items...

Dhanu K

Guest

How do you clean and seal a basement concrete floor?

Clean the ConcreteStep 1: Clean the Surface. First, thoroughly sweep the surface of all dirt and debris.Step 2: Deep-Clean. Remove any grease, oil, mastic or paint. ... Step 3: Mop and Dry. After the stains have been removed, mop with floor cleaner and water. ... Step 4: Fill Cracks.Nov 3, 2020

Chris Halcrow

Guest

Can I paint a concrete driveway?

Yes you can, painting your driveway will extend your driveway''s life as well as improve the value of your property. Driveways are exposed to harsh weather conditions all year round, as well as gas leaks and oil spills, so if it doesn't get proper attention, then the concrete may chip and crack.

anmol.majhail

Guest

How do you make an old concrete driveway look good?

6 Ways to Make Your Driveway Look Amazing#1: Etching. Nothing sets your driveway apart from the rest like etching. ... #2: Staining. Tired of plain old gray? ... #3: Stamping. Similar to staining or etching, concrete stamping can also spruce up your driveway with color and a pattern. ... #4: Weeding. ... #5: Pavers. ... #6: Resin Bound.Sep 19, 2018

George Lvov

Guest

How much does it cost to remove concrete UK?

Cost to remove concrete driveway On average, you can expect the cost for this type of job to start at £50 per square metre, but total costs tend to sit between £1,500-£2,500. Of course, this price can increase if the driveway is larger than average or requires specialist equipment for removal.

Desmond Gold

Guest

How do you repair concrete after removing tack strips?

Wipe across the damaged concrete with a wire brush to remove cracked or chipped edges from the tack-strip nail holes.Sweep the area with a broom or small brush to remove any loosened concrete, dirt or other debris.Mix a quantity of epoxy concrete patch according to the manufacturer's directions.More items...

Casimir Crystal

Guest

Can I vacuum plaster dust?

Can we use the Dyson V10 to suck up plaster dust or finer particles or is it bad for the vacuum? It will ruin any home vac. You'll want a decent shop vac for that. ... That will do the motor in that plaster will go right through the cyclone and pre motor filter.

sinoohe

Guest

Do you have to remove paint from concrete before painting?

Doing the prep work before you repaint a concrete floor avoids a peeling paint job later. Concrete paint can be purchased in either latex or oil-based epoxy enamel. ... Remove all flaking, peeling paint using a scraper and wire brush. Smooth and sand rough edges using 100-grit sandpaper.

bigbug

Guest

Should I seal my concrete shop floor?

In order to effectively protect your garage floor from stains, oil or otherwise, you need to seal your floor with a good concrete sealer. Concrete sealers help protect your concrete from natural elements, such as water damage, as well as from inadvertent error, like the spilling of oil.

Ben Smith

Guest

Do cement trucks always spin?

A large motor, separate from the engine, rotates the drum on the truck body, and a series of blades or a screw powered by the same motor keeps the aggregate, water and cement in constant motion. ... Most cement manufacturers suggest keeping the time between mixing and pouring to 90 minutes at most.

Brian Thompson

Guest

How do you remove concrete and plant grass?

Use a shovel or garden hoe to eliminate all debris from the planting site.

Scrape off chipped concrete pieces and pull out any underlying rebar and metal ties left from the concrete.

Check for layers of gravel beneath the old concrete.

Remove gravel to provide a smooth surface of bare soil..

Toddleson

Guest

How do you remove old concrete driveway?

If you're working by hand:Starting at a corner, break up a small section of the driveway using your jackhammer.If necessary, use a sledgehammer to break any large chunks of concrete into smaller pieces.Use a shovel and wheelbarrow to move the debris into your concrete dumpster or pickup truck.More items...•Apr 18, 2017

Ahmad Awais

Guest

How do you remove old paint from a concrete porch?

PROJECT SUMMARYClean the concrete surface thoroughly and let dry.Scrape peeled or chipped paint.Apply paint stripper and wait.Remove paint stripper residue.Reapply paint stripper as necessary..

Kevin Burke

Guest

What do you spray on concrete forms?

Fill a hand-pump sprayer with oil. Any type of oil will prevent concrete from sticking to wood. Spray the surfaces that will face the wet concrete with a heavy saturation of oil. Allow the oil to penetrate the wood for 15 to 20 minutes.

dustbuster

Guest

How do I get rid of the odor of spilled heating oil in my concrete basement?

Try using the following methods. Laundry detergent and baking soda: One way you can start to cover the smell is by sprinkling powdered laundry detergent or baking soda on the affected area. As with kitty litter and sawdust, this will keep the oil from spreading and will absorb some of the oil.

Mike

Guest

How do you seal concrete to concrete?

Here's a step-by-step summary of how to seal concrete:Remove all oil, grease, stains, dirt, and dust from the concrete.Strip any existing sealer from the surface.Open up the concrete with an etching solution.Apply a thin coat of sealer using a roller or sprayer.Wait for the first layer of sealer to dry.More items...

Seth Ladd

Guest

What removes oil stains from concrete at home?

The four best ways to remove oil stains from concrete are:Wash away the oil with a strong detergent, and a scrub brush or sponge.Use a concrete cleaner or degreaser to loosen and remove the oil.Apply a poultice that will break down the oil and suck it from the concrete.More items...

tmdavison

Guest

How do you remove cement from your body?

Upon contact with cement, remove contaminated clothing right away. If cement is on your skin or eyes, rinse it off immediately with cool or room temperature water for at least 15 minutes.

DevSolar

Guest

How do you remove ceramic tile from a concrete floor?

Removing Porcelain and Ceramic Tile from ConcretePick a Place to Start. If you have a chipped or broken tile, that's usually the best place to start. ... Remove a Tile. Simply place your chisel into the seam at an angle and hit the end with your hammer to loosen the tile. ... Rinse and Repeat. ... Removing Thinset and Adhesive.

David C. Rankin

Guest

How do you remove concrete overlay?

Once you have a place started where the overlay is broken through, continue to remove the concrete overlay. This is easily done by prying up the concrete from underneath and breaking it into smaller pieces. Use a flat scraper with a long handle to drive under the overlay and lift up.

NicoE

Guest

How do you remove dried cement from tiles?

How to remove thick cement from tilesScrape.

Remove as much cement as you can from the tiles using a scraper.Apply acid.

Apply phosphoric acid to the cement, following the manufacturer's instructions exactly.Scrub.

Once loosened, scrub the cement away with a scouring pad or a brush.Rinse.

...

Clean.

...

Rinse again..

Kirill Rakhman

Guest

How do you remove hard plaster from a brick wall?

Use a wide bricklayer's chisel and a masonry hammer to chip away plaster from the brick, working your way from the bottom of the wall to the top. A hydrochloric acid solution applied with a wire brush can be used to remove excess plaster residue and clean the surface to expose the beauty of the brick.

monfresh

Guest

How do you remove hardened concrete from tools?

Remove Dried Concrete and Mortar Sakrete Concrete Mortar Dissolver is a user friendly solution that dissolves concrete and mortar from tools and other surfaces. Completely saturate the area of hardened concrete or mortar to be removed with undiluted Concrete Mortar Dissolver.

Prasanth Bendra

Guest

How do you remove heavy texture from plaster walls?

If the area was texturized with joint compound, water and a drywall knife can generally remove most of the texture. Continue with gentle scraping to remove the texture. If the texture was created with plaster, water won't help and you can continue to the next step. Gently sand the surface of the wall with sandpaper.

sarnold

Guest

How do you remove mold from plaster walls?

Remove mold stains from walls. Mix a solution of one part bleach to three parts water in a spray bottle, and thoroughly saturate the moldy areas of the wall. Open a window and/or keep a fan running as you work; bleach fumes are unpleasant and can be irritating to the lungs.

ZahiC

Guest

How do you remove textured plaster from walls?

If the area was texturized with joint compound, water and a drywall knife can generally remove most of the texture. Continue with gentle scraping to remove the texture. If the texture was created with plaster, water won't help and you can continue to the next step. Gently sand the surface of the wall with sandpaper.

Steve

Guest

How do you seal a new concrete driveway?

Concrete sealers can be applied with a roller or with a sprayer, depending on the product. Refer to the manufacturer's label instructions for the recommended method. Generally speaking, solvent-based (oil-based) sealers are best applied by spraying, while water-based sealers are better applied with a roller.

ziad-saab

Guest

Is diesel a concrete release agent?

Bad concrete form releases include diesel oil, heating oils, used motor oil, etc. Good, chemically active, soapy types of concrete form release agents are derived from soybeans, flaxseed, trees, hogs, cattle, fish, etc. and produce fewer bug-holes, stains and surface irregularities than bad types.

s.kuznetsov

Guest

Is it cheaper to blacktop or concrete driveway?

The cost of an asphalt driveway is typically cheaper than concrete, costing $2.00 – $4.00 per square foot.

Asphalt prices tend to fluctuate with fluctuations in crude oil prices.

In contrast, a concrete driveway costs between $4.00 – $6.00 per square foot for a standard installation..

TomAugspurger

Guest

Should I seal concrete garage floor?

Because garage floors are protected from outdoor elements, they don't generally need sealed as often as a concrete driveway.

However, most garage floors are made from concrete, making them susceptible to cracking and moisture intrusion from oil spills, antifreeze leakage, and other household chemicals..