Because concrete is a very porous material, it will absorb any moisture that it contacts. This can cause pooling. Without crushed stone, pooling water will settle under it and erode your slab. Adding a layer of crushed stone will add proper drainage, as well as create a barrier between your slab and the ground.

Answered by: Marcus Lind Date created: Jun 24, 2022

## How many bags of cement do I need for a 10x10 slab?

Asked By: nosklo Date created: Jun 23, 2022

For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags. If we add an extra 10%, that's an extra 8 60-pound bags or 6 80-pound bags.

Answered By: crypdick Date created: Jun 26, 2022

## How many bags of concrete do I need for a 6x6 slab?

Asked By: Mahdi-Malv Date created: Jun 10, 2022

0.667 cu. yds. How many concrete bags would I need for a 6 ft x 6 ft x 6" slab? 29.9 x 80lb Concrete bags.

Answered By: scottlittle Date created: Jun 13, 2022

## How many bags of concrete do I need for a 4x8 slab?

Asked By: Nishant Nawarkhede Date created: Jun 14, 2022

Your project is 32 square feet at a depth of 4”. Here is the quantity that you will need for your slab. Quikrete Concrete Mix: 24- 60lb bags.

Answered By: dev sandbox Date created: Jun 16, 2022

## What do you mix cement with?

Asked By: Tim Schmelter Date created: Jun 08, 2022

Mixing Concrete: Sand, Cement, Gravel, and Water. When mixing by hand, it is essential to thoroughly mix the concrete to get consistency throughout the mixture. If you need to mix a small amount, for instance half a bucket, place the stone and sand and finally the cement into the bucket.7 Jan 2020

Answered By: mosc9575 Date created: Jun 10, 2022

## How many coats of plaster do you need?

Asked By: Miguel Date created: Jun 21, 2022

The number of coats that you will need to apply depends on how deep the hole is. Any hole under half an inch should only require one coat. Deeper holes will need two coats. Just like when you're plastering an entire wall, make sure you scratch the first layer of plaster before you apply another coat on top.

Answered By: Carlos M Date created: Jun 21, 2022

## Can you pour concrete on clay?

Asked By: breq Date created: Jun 09, 2022

Unfortunately, if you have clay-heavy soil, then you may run into difficulty when pouring a slab. The clay can compress under the weight of the concrete, causing the slab to shift or sink over time. With proper preparation, however, it's possible to pour a slab on clay soil without encountering these problems.

Answered By: Diego Woitasen Date created: Jun 11, 2022

## Do I need a concrete footing for a retaining wall?

Asked By: Lehane Date created: Jun 22, 2022

A concrete footing serves as the foundation of many construction projects. ... If you plan to use brick, cinder block or stone that will include the use of mortar, then a concrete footing is recommended. If you are building a segmental retaining wall, then you will not need a footing.

Answered By: Alexander Artemenko Date created: Jun 24, 2022

## Can you lay concrete without rebar?

Asked By: micronyks Date created: Jun 18, 2022

It's false economy to do concrete without putting in rebar and mesh.

Rebar around the perimeter at the least, and mesh over the rest.

Pull it up when pouring so it is not resting on the bottom of the slab.

You don't need the fancy rebar supports, a stone or broken brick will work just as well..

## How do you run a pipe under a concrete slab?

Asked By: Aliaksandr Sushkevich Date created: Jun 14, 2022

In six simple steps you can dig under concrete:Attach drill pipe.Connect garden hose.Dig a small ditch.Start your bore.Add more drill pipe (if necessary).Pull piping through.

Answered By: mikemaccana Date created: Jun 14, 2022

## How do I get rid of rats under my concrete slab?

Asked By: pvpkiran Date created: Jun 09, 2022

Answer: If the patio slab is not connected to the house slab you can use a Giant Destroyer to help eliminate the rat. If there are many tunnels or if it is in an area where you cannot seal up the entrances you may want to consider using rat poison baits instead such as Fastrac or Contrac.

Answered By: Ólafur Waage Date created: Jun 11, 2022

Professor

### How many bags of concrete do I need for a 4x4 pad?

The calculator will indicate the number of 60 or 80 pound bags of QUIKRETE® Concrete Mix you need to build a 4″ or a 6″ slab.

Professor

### Can you run a gas line under a concrete slab?

Otherwise you could bury a pvc pipe in the concrete to run your gas line thru. Yes, you can bury the gas line. First I would bury a straight pipe larger than your gas line under the patio and then run the gas line in the pipe. If you ever need to replace the gas line it will be easy to remove.

Professor

### How many bags of concrete do I need for a 10x20 slab?

A 60-pound bag yields . 017 cubic yards, and an 80-pound bag yields . 022 cubic yards. For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags.

Professor

### How much does it cost to replace a sewer line under a concrete slab?

The cost to replace a sewer line under a slab costs \$3,000 to \$5,000 for smaller jobs and \$15,000 to \$20,000 total for larger jobs.

Trenching under a slab can cost an extra \$150 to \$200 per foot..

Professor

### How many bags of concrete do I need for a 8x8 slab?

How many concrete bags would I need for a 8 ft x 8 ft x 6" slab? 54 x 80lb Concrete bags. How much does it cost to pour a 8'x8' x6" slab? Ready-mix costs approx \$277.86.

Professional

### Do I need rebar for small concrete slab?

You do not need rebar for any slab if you make it thick enough and space the joints properly. Rebar in jointed pavement is there to counter the cupping effect of thermal expansion. I always recommend the use of rebar or at least rewire. Any concrete slab can crack.

Professional

### Do you need a footer for a concrete slab?

All 3 types of slabs will need a footer and a slab of at least 4″ thick. The footers depth needs to be the depth of the frost line or as per local code, but no less than 12″ deep. ... Slab Foundations Like all foundations, the slab starts with concrete footers poured 24 inches below projected finish grade.

Professional

### Can concrete cure under water?

Water Cure Concrete made with Portland cement will harden even if it is completely under water.

In fact, one technique for curing a concrete slab is to build a soil dam around the perimeter of the slab, flood the slab with water and keep the slab covered with water for a week..

Professional

### How do I find a water leak under a concrete slab?

Signs Of A Leak Under Concrete1). There is water or damp spots on your floor. If hot-water lines are leaking, this may also lead to warm spots on your floor. ... 2). You can hear the sound of rushing water underneath your floor. ... 3). There is a significant increase in your water bill.Jan 10, 2021

Professional

### How do you install moisture barrier under concrete slab?

Most exterior slabs do not need a vapor barrier. ... In general, place the concrete slab directly on top of the vapor barrier, with the subbase below. ... The vapor barrier can be placed under the subbase, if the building is closed in when the dry subbase material is placed.More items...

User

### Do I need cement board for stone veneer?

Natural stone veneer is heavy and should not be installed over drywall; cement backerboard or masonry applications are recommended.

User

### Do I need mesh in my concrete slab?

Concrete is strong in compression, but not under tension. So, if it flexes, like a slab with a vehicle on top of will do, it cracks at the bottom whre the flexing becomes tension. ... Mesh will help mitigate the chances of cracking of the slab due to differential settlement.

User

### Do you need Thinset under cement board?

Not only is thinset a critical component underneath cement board but the other critical component is the fasteners.

And you won't have the fasteners if you are trying to install it over concrete..

User

### How do you run a conduit under a concrete slab?

Select a pipe of sufficient diameter for the desired excavation width. ... Dig a small trench on each side of the concrete slab. ... Measure the width of the concrete slab. ... Push the angled end of the PVC pipe into the soil in the trench on one side. ... Tap the other end of the PVC pipe with your sledge hammer.More items...

User

### How many tons of crushed concrete do I need?

To figure out the how many tons you will need is not hard to do. You will have to know that the standard weight contractors use for crushed stone is 2700 pounds per cubic yard. Multiply the number of cubic yards by 2700 and divide by 2000. This value is the number of tons that you will need.

Guest

### How much crushed concrete do I need?

Beside above, how much crushed concrete do I need calculator? In the construction world, most materials are measured in cubic yards. Multiply the length (L), in feet, by the width (W), in feet, by the height (H), in feet, and divide by 27. This will tell you how many cubic yards of crushed stone you need.

Guest

### Do you put cement board under bathtub?

You don't need any cement board under the tub. It is far more important to have a sturdy layer of ply under the tub.

Guest

### How do you fix a void on a concrete slab?

– Sand-Cement Grout A sand-cement grout can be used to fill voids under concrete slabs. This mix of sand, cement, and water is pumped through holes drilled to fill up the voids. While this method of slab jacking is cost-effective, there are major drawbacks to opting for this type of repair.

Guest

### Can concrete be poured over stones?

Simply pouring concrete onto the ground will expose it to elemental erosion that will cause cracking and sinking. Similarly, if there are roots or plants under your slab, they may rot and cause unevenness. Pouring concrete over crushed stone, however, will eliminate these worries.

Guest

### Can you put footings under concrete slab?

edit - To put footings under the slab, you can cut holes wherever needed, excavate for footings (Sonotubes or concrete piers or similar) and then patch the concrete slab.

Guest

### Do I need insulation under a concrete floor?

Creating an insulation layer and a vapor barrier between the concrete slab and the ground beneath it is the best practice in insulating basement floors.

The insulation barrier will help keep warm air in, and the vapor barrier will keep unwanted moisture out..

Guest

### How much insulation do I need under a concrete floor?

A 50mm thick layer of proprietary floor slab insulation is usually enough to reach and maintain the target U value but this should be checked with an architect first. Insulation sheets should be laid tightly together with the joints staggered to avoid movement.

Guest

### Should I put cement board under tub?

You don't need any cement board under the tub. It is far more important to have a sturdy layer of ply under the tub.

Guest

### How do you backfill under a concrete slab?

Drill at least four holes through the slab at a point that's centered on the void beneath. ... Connect a hose to a slabjacking pump, then run the hose to the holes leading to the void. ... Mix the fill material in a wheelbarrow, using a spade. ... Fill the pump with the fill material and set it to a pressure of 10 psi.More items...

Guest

### Will concrete cure under water?

Water Cure Concrete made with Portland cement will harden even if it is completely under water. In fact, one technique for curing a concrete slab is to build a soil dam around the perimeter of the slab, flood the slab with water and keep the slab covered with water for a week.

Guest

### How many bags of cement do I need for a 4x4 slab?

Your project is 32 square feet at a depth of 4”. Here is the quantity that you will need for your slab. Quikrete Concrete Mix: 24- 60lb bags.

Guest

### Do I need DPM on concrete floor?

Do I need a DPM under laminate flooring? Simply put yes. In order to prevent damp rising through the concrete floor and causing issues, a DPM should be used under all final floor types including wood flooring, laminate, vinyl and floor tiles.

Guest

### How do you break concrete slab by hand?

InstructionsDig Under the Concrete. Dig out the soil, gravel, or other material from under the concrete, using a shovel and a pickax. ... Strike the Concrete. Lightly sprinkle the concrete with water to minimize dust. ... Pry Off Stubborn Pieces. ... Move the Concrete Chunks With a Hand Truck.Feb 19, 2020

Guest

### Do I need concrete reinforcing mesh?

And yes, mesh is important: Concrete is strong in compression, but not under tension. So, if it flexes, like a slab with a vehicle on top of will do, it cracks at the bottom whre the flexing becomes tension. Steel mesh will prevent this to a large degree and hold it all together.

Guest

### Can you add footers to a concrete slab?

edit - To put footings under the slab, you can cut holes wherever needed, excavate for footings (Sonotubes or concrete piers or similar) and then patch the concrete slab.

Guest

### Can you pour concrete on soft ground?

If you drive over a concrete slab that's got soft ground under it, the concrete wants to bend and stretch. ... If the concrete does develop a hairline crack, the crack should not open with the steel in place. Compacting the soil under the slab before the pour also prevents tension cracking.

Guest

### Can you pour concrete on top of clay?

Unfortunately, if you have clay-heavy soil, then you may run into difficulty when pouring a slab. The clay can compress under the weight of the concrete, causing the slab to shift or sink over time. ... With proper preparation, however, it's possible to pour a slab on clay soil without encountering these problems.

Guest

### Do I need a footer for concrete patio?

You really do not want the patio level with the house threshold, too easy for water to get in to the house. As for the slab, it will not settle if you prepare the subgrade correctly. You need the footers to support the structure, the slab is just there to walk on, and has no structural importance.

Guest

### Do you need a vapor barrier under concrete driveway?

The application of vapor barrier in exterior concrete is unnecessary due to the fact that water penetration does not matter. Any slab on grade that is enclosed and on the interior of a building should have a vapor barrier installed prior to pouring concrete, especially if flooring will be applied.

Guest

### Do you need concrete under pavers?

Installing pavers is very similar to concrete installation. You must start with a solid base and foundation. Most frequently, this involves digging down into the ground and removing the existing dirt and replacing it with gravel and sand.

Guest

### Do you need gravel under a concrete patio?

Yes! A strong gravel base is required when building a concrete patio in order to prevent the concrete from shifting or cracking. Adding gravel under the concrete also provides a level surface for your foundation and adds proper drainage when there is pooling water.

Guest

### Do you put plastic under concrete slab?

In California they place sand between slabs and plastic vapor barriers—in Florida they don't. Almost everywhere (except “California”) that slabs are placed on the ground—a plastic sheet—a vapor barrier—is located directly under the concrete slab and on top of the ground (Photograph 1).

Guest

### Do you need gravel under concrete footing?

Registered User. permanent wood foundations require gravel, not concrete or soil for the footings - every situation is a little different, but all footings need to bear on the soil/gravel/bedrock/ whatever is supporting the structure equally, or it's going to settle at different rates.

Guest

### Do you need sand under concrete slab?

One reason it is used as a backfill or sub-grade material. As with all material, it has to be placed correctly and compacted properly. Sand needs to remain damp as well as other material before placement of the concrete. If you want to build a road, use gravel, but this does not mean you will not have issues.

Guest

### Do you need to put wire in a concrete driveway?

Wire mesh, like Rebar reduced the cracking and any uplift in the concrete driveway. Rebar will be used if there is a structural reason, meaning you need to carry the weight of the slab to pilings or plan to build above the slab. For a driveway, just use the wire, lap it one box around.

Guest

### How do you break concrete at home?

InstructionsCover the concrete slab with 4 mil plastic sheeting if you're working near windows.Dig under the concrete if you're able to do so.Start to break the concrete, starting six inches from the edge and working your way in. ... Pry with a long bar or wrecking bar as you go. ... Cut any mesh wire with bolt cutters.More items...•Oct 14, 2019

Guest

### How many bags of concrete do I need for a 10x10 slab?

For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags. If we add an extra 10%, that's an extra 8 60-pound bags or 6 80-pound bags.

Guest

### How many inches of gravel do you need for a concrete slab?

Excavate the slab area to a depth of about 7 inches, allowing 3 inches for a gravel base and 4 inches for concrete.

Guest

### Will concrete crack without rebar?

Really depends on what the slab is used for but in general no you can install wire mesh or use fibered concrete. However you do need something to tie the concrete it just doesn't have to be rebar. You do not need rebar for any slab if you make it thick enough and space the joints properly. ... Any concrete slab can crack.

Guest

### Do you need a footing for a concrete slab?

While not a requirement, a concrete slab foundation provides a solid, clean surface for your steel building and can help it last longer. Since the building will require anchoring to minimize shifting, pouring a concrete slab gives you a chance to pour footings as well.

Guest

### How many bags of concrete do I need for a 12x12 slab?

Enter the size of the slab you want to build in square feet. The calculator will indicate the number of 60 or 80 pound bags of QUIKRETE® Concrete Mix you need to build a 4″ or a 6″ slab. (All yields are approximate and do not include allowance for uneven subgrade, waste, etc.)

Guest

### Do I need gravel under my concrete slab?

Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting.

Gravel is especially important in clay soil because it doesn't drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains..

Guest

### Do you need to use thinset under cement board?

Not only is thinset a critical component underneath cement board but the other critical component is the fasteners. And you won't have the fasteners if you are trying to install it over concrete.

Guest

### Should you put plastic under concrete slab?

Recently, though, research has shown that the old traditional layer of 6-mil Visqueen (polyethylene plastic) under the slab is seldom effective for two main reasons: Although it may seem water-tight, this grade of material allows a lot of water vapor to pass through.

Guest

### How many bags of concrete do I need for a 4x8 pad?

Here is the quantity that you will need for your slab. Quikrete Concrete Mix: 24- 60lb bags.