How much crushed concrete do I need?

For laying bricks and blocks in normal applications (SABS Class II) To lay 1000 bricks = 3 bags cement + 0.6 cu. m. sand.

For every m2 of wall you will need ten concrete blocks. For every ten blocks you will need two 25kg bags of bricklaying mortar. If you are working on a larger project it may be more economical to mix your own mortar. For bricklaying you need to mix one part of cement to five parts building sand.

Typically, 1m3 of concrete is made up of 350Kg of cement, 700Kg of sand, 1,200Kg of chippings and 150 Litres of water..

For every m2 of wall you will need ten concrete blocks. For every ten blocks you will need two 25kg bags of bricklaying mortar. If you are working on a larger project it may be more economical to mix your own mortar. For bricklaying you need to mix one part of cement to five parts building sand.

As I recall, a 60# bag of concrete is about .

5cf, so you'd need 3 bags per hole..

How many concrete bags would I need for a 8 ft x 8 ft x 6" slab? 54 x 80lb Concrete bags. How much does it cost to pour a 8'x8' x6" slab? Ready-mix costs approx $277.86.

Each hole for the terminal posts must be 8 inches in diameter and 30 inches deep, requiring 0.85 cubic feet of concrete to fill.

With a brief look, a 20x20 area at 6 inches deep, you would need approximately 10.52 tons or 7.41 cubic yards of gravel. Concrete reinforcing is also recommended in high traffic areas and medium to large areas.

12,000 pound two-post lifts (and higher capacity): Six (6) inches of concrete at 3000 PSI is required.

For concrete, the formula for volume is as follows: length x width x thickness. To determine how many bags of concrete you will need, divide the total cubic yards needed by the yield.

To figure out the how many tons you will need is not hard to do. You will have to know that the standard weight contractors use for crushed stone is 2700 pounds per cubic yard. Multiply the number of cubic yards by 2700 and divide by 2000. This value is the number of tons that you will need.

Concrete blocks are much easier to calculate. Each block is 450 x 215 x 100. Ten blocks will construct approximately 1 square meter of wall, with 1 bag of sand/cement mix enough for 10 blocks.

In most cases a 50-pound bag of quick-dry concrete should suffice. Saturate the concrete. For a 50-pound bag you will need about a gallon of water. Be sure to leave support beams in place for 4 to 6 hours or until concrete is dry.

How many concrete bags would I need for a 5 ft x 5 ft x 6" slab? 20.8 x 80lb Concrete bags.

STANDARD ICFSTANDARD ICF$13.95,$15.95 or $17.95Concrete$100.00 Per yard (1 yard fills 10.5 blocks)Labor$30.00 per hour, 5 blocks per man hourRe-bar$.30 per footPump$250 minimum, Plus $3.00 per yard1 more row

As to how many bags....a 55 gallon drum filled clear to the top is actually closer to 60 gallons. And 60 gallons is 8 cu ft. So if you buy 60lb bags, those do 1/2 cu ft each so you would need 16 of them. IF you buy 80lb bags (2/3 cu ft) you would need 12 bags.

You will need 45 bags of concrete mix to make a cubic yard of concrete.

How Much Concrete per Vinyl Fence Post?Post SizePost Height (above surface)80lb Bags Required4×43-4ft double-triple rail9 inch hole15×53-4ft double-triple rail12 inch hole15×55-6ft semi & privacy122

For example, a sono tube with a 10" diameter and a 4' depth requires 0.08 cubic yards of concrete..

The depth of the hole should be 1/3-1/4 the post height above ground (i.e., a 6-foot tall would require a hole depth of at least 2 feet).

Plan on at least 5 minutes per cubic yard, for unloading time. How much concrete do I need? Order this much concrete, for these standard pool sizes. 12 x 24 – 5 yards, 14 x 28 – 6 yards, 16 x 32 – 7 yards, 18 x 36 – 8 yards and a 20 x 40 – 9 yards.

In order to have enough concrete for one cubic foot, you'll require 2.2 bags of 60-lb concrete.

Since bags are only sold in whole (not half, or quarter) quantities, you'll need to purchase three (3) 60-lb.

bags for one cubic foot..

Multiply the square footage by the depth in feet to find the volume of the space in cubic feet. Volume is found by measuring length × width × depth. Finally, divide the cubic footage by 27 to find the volume in cubic yards. This is the amount of concrete needed.

Once you know how big the room is and ideally know how many square meters are in it, you can simply divide that figure by 9 to give you about how many bags of multi finish plaster you will need. Multi finish covers 10m2, but I say 9m2 to all allow for wastage.

To plaster 100 square metres (15 millimeters thick) you will need: 14 bags cement + 2,25 cubic metres sand. Using masonry cement complying with SANS 50413 class MC 12,5X. To plaster 100 square metres (15 millimeters thick) you will need: 20 bags cement + 2 cubic metres sand.

If there is a layer of water across the top, you've added too much. The rule of thumb is about 5 pounds of water to an 80 pound bag of concrete mix.

Crushed concrete costs $11 to $53 per ton, around $16 to $75 per cubic yard, and $1 to $3 per cubic foot, with prices depending on the quantity.

Various instructions and regulations therefore also state that you need about 56 packs of dry concrete of 40kg each for 1m³, which results in about 17.86 litres of liquid concrete per pack.

Mortar calculation for tile flooring We need 1.5 m3 volume of wet cement mortar that means, we need this much volume after adding water to cement and sand mix. Dry volume of mortar is considered as 25% of more of wet volume.

To calculate how much concrete you need, you need to know the post size you are going to use and how many posts you are installing. Your post diameter and height determine how big each hole needs to be. As stated above, fence post holes should be 3 times the diameter of your post and 1⁄3 as deep as your post.

Each 80 lb (36.3 kg) bag of QUIKRETE® grout will fill the cores of approximately 3 standard 8" × 8" × 16" (203 × 203 × 406 mm) block.

45 bagsPure cement, sand and crushed rock all have about the same density, so a block of pure cement measuring 1 cubic yard of volume (about 3,600 pounds) will contain 45 bags of cement.

To determine how many bags of concrete you will need, divide the total cubic yards needed by the yield. Use the following yields per each bag size: 40 pound bag yields .011 cubic yards. 60 pound bag yields .017 cubic yards.

Concrete Slab Prices By SizeSlab SizeSquare FeetAverage Cost Installed15x15225$1,38820x20400$2,46824x24576$3,55420x30600$3,7026 more rows

A five gallon bucket can hold . 45 cubic feet of concrete when mixed with water. In other words, one 60 pound bag of pre-mix or an equivalent Portland Cement/rock and sand mix.

Apply the Sealant Depending on how porous your concrete is, a gallon of sealer will cover 250 to 500 square feet.

Crushed concrete costs $11 to $53 per ton, around $16 to $75 per cubic yard, and $1 to $3 per cubic foot, with prices depending on the quantity. Leftover concrete and broken asphalt get crushed and recycled, which is a cheaper and more eco-friendly solution for gravel driveways.

To lay 1000 bricks = 3 bags cement + 0.6 cu. m. sand. 1 Bag of cement to 3 wheelbarrows of building sand.

BUDGET: You can achieve a homemade Venetian plaster finish for roughly $6 to $11 per 100 square feet, considering you'll need $2 to $3 for pre-mixed joint compound, $0.10 to $0.50 for latex colorant, and $4 to $7 for tinted glaze.

For example, a sono tube with a 10" diameter and a 4' depth requires 0.08 cubic yards of concrete.

How to calculate concrete:Determine how thick you want the concrete.Measure the length and width that you'd like to cover.Multiply the length by the width to determine square footage.Convert the thickness from inches to feet.Multiply the thickness in feet by the square footage to determine cubic feet.More items...•Apr 23, 2018

Quantity of cement = 1/13 × 1.54 m3 × 1440 kg/m3 = 170 kg, no of bag cement for 1m3 m7. 5 concrete = 170/50 = 3.4. If rate of cement = INR 400 per bag, then cost of 3.4 bags cement = 3.4 ×400 = INR 1360.

How do I calculate how much concrete I need for a slab?Measure the area in feet.Multiply length by width, and then by thickness.Divide the resulting number by 27 to find cubic yards.

How do I calculate how much concrete I need for a slab?Measure the area in feet.Multiply length by width, and then by thickness.Divide the resulting number by 27 to find cubic yards..

For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags. If we add an extra 10%, that's an extra 8 60-pound bags or 6 80-pound bags. Whatever the size of your project, use the formula above to calculate how much concrete you'll need!

1 Cubic Meter of Concrete 1m3 of concrete = 150l water + 250kg cement + 700kg sand + 1200kg aggregates.

For bricklaying you need to mix one part of cement to five parts building sand. It does not matter how you measure a part, be it by weight or by the bucketful, so long as you use the same means of measuring for both sand and cement.

The mixing ratio is 1 part cement and 5 parts sand, and if the plaster is too harsh, 0.5 to 1 part of lime can be added.

How Many Bags of Concrete do you Need?Bag SizePre-mix Bags Needed to Fill1/4 cu yd1 cu yd40 lb bags239060 lb bags156080 lb bags1245.

Mixing 1 part cement to 6 parts ballast creates concrete suitable for driveways, paths and patios, and increasing the ratio to 1:8 gives foundation-strength concrete..