Best answer

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it.

Answered by: Arnaud Develay Date created: Jun 22, 2022

How thick should plaster skim be on plasterboard?

Asked By: Zaz Date created: Jun 09, 2022

You should aim for a thickness of around 1–2mm. The plaster you have mixed should last around 40 minutes before starting to set. Cover the entire surface in one go — don't stop halfway.

Answered By: dash Date created: Jun 11, 2022

How thick should plaster be on plasterboard?

Asked By: Patryk Date created: Jun 13, 2022

You should aim for a thickness of around 1–2mm. The plaster you have mixed should last around 40 minutes before starting to set.

Answered By: Laryx Decidua Date created: Jun 16, 2022

How thick should a concrete slab be for a mobile home?

Asked By: Mark Bramnik Date created: Jun 23, 2022

4 to 6 inches

Answered By: Ryan Bigg Date created: Jun 25, 2022

How thick does a concrete slab need to be for a garage?

Asked By: Yagiz Degirmenci Date created: Jun 20, 2022

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region.

Answered By: Maurits Evers Date created: Jun 23, 2022

How thick should cement board be under tile floor?

Asked By: MojixCoder Date created: Jun 18, 2022

Floors: A 1/4-inch minimum thickness is needed, but thicker panels are also fine. Walls: Use 1/2-inch or 5/8-inch-thick cement board, not 1/4-inch. The extra thickness is needed to span the studs and provide a solid base for the tile.

Answered By: RbMm Date created: Jun 20, 2022

How thick should tile cement be?

Asked By: Paul Lammertsma Date created: Jun 09, 2022

3mmFor thin bed fixing of tiles, the minimum finished thickness of the adhesive should not be less than 3mm. Hairline cracks of up to 2mm in concrete should be bridged.

Answered By: JRichardsz Date created: Jun 12, 2022

How thick should a concrete slab be for a shed?

Asked By: Martin Brandl Date created: Jun 13, 2022

Recommended Thickness of Concrete Slabs Shed Slabs: 3 1/2 inches thick. Shed floors that are being used for studio sheds or workshops will use a 3 1/2" thickness. Driveways: 4 inches, some areas require 5 inches. Many garage sheds need a driveway approaching the large shed door.

Answered By: Don McCurdy Date created: Jun 16, 2022

How thick should a concrete driveway be?

Asked By: Joseph Arriaza Date created: Jun 21, 2022

four inchesAs for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.

Answered By: Karoly Horvath Date created: Jun 21, 2022

How thick does concrete need to be for heavy equipment?

Asked By: Alexander Kim Date created: Jun 18, 2022

Six inchesSix inches of thickness should be more than adequate for areas where heavy equipment will be driven and parked. For lesser loads, four inches.

Answered By: Gary Russell Date created: Jun 20, 2022

How thick is the plaster on a gunite pool?

Asked By: Ron Date created: Jun 09, 2022

3/8-inchSwimming pool plaster topcoats should be of no less than 3/8-inch thickness.

Answered By: Davor Lucic Date created: Jun 10, 2022

Related Question Answers

Marc Audet

Professor

How thick should a cement driveway be?

As for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.

metakermit

Professor

Can I build a garage on a concrete slab?

You may want to consider a 6" thick slab for larger vehicles such as trucks or RVs. For a garage WITHOUT a floor - BUILT ON SITE: Prepare a level concrete slab at least 4” thick and to the exact, outside, dimensions of your garage. You may want to consider a 6" thick slab for larger vehicles such as trucks or RVs.

Samathingamajig

Professor

How do you prepare concrete for epoxy coating?

Preparing Concrete Floors for Epoxy CoatingRemove clutter and furniture from the floor.With a broom, sweep away any dirt or dust from the floor.Sticky material or thick mud should be removed with a metal putty knife.A course brush and a chemical degreasing agent should be used to scrub away greasy areas.More items...•Oct 8, 2020.

andrew cooke

Professor

How do you prepare the ground for a concrete garage floor?

Good ground preparation starts with removing the topsoil. Then, if the soil has not previously been "disturbed" (i.e., dug up), a four-inch layer (minimum) of gravel or stone should be added. (Soil that has been dug up before should be compacted.) The gravel or stone also needs to be compacted.

murgupluoglu

Professor

How thick should a concrete slab be for a basketball court?

3500 PSIBase Material Many basketball courts are built over a 4” thick concrete slab using 3500 PSI concrete and 1/2″ rebar reinforcements. Concrete is considered ideal for basketball courts as a permanent structure that when done right will not require any maintenance.

NishanW

Professional

How thick does the concrete need to be for a car lift?

100mmThe minimum and recommended thicknesses of concrete slab for car hoists. Garage Equipment's two and four post hoists require a minimum of 100mm (about 4”) of reinforced concrete slab to be safely installed.

Björn Pollex

Professional

How thick of a concrete slab for a hot tub?

about 4 inchesConcrete Slab The base of reinforced concrete should be about 4 inches thick and be able to withstand a weight of at least 115 pounds per square foot, especially for larger spas. The concrete should be fully cured prior to placing the tub.

beerwin

Professional

How thick should a concrete pool be?

between three and four inchesGenerally, the pool walls need to be between three and four inches thick. Smooth the pool walls with your trowel, as you did for the base. Now the concrete has to cure properly before you can fill it with water. The concrete curing process allows the concrete to reach maximum strength and takes approximately 28 days.

Selcuk

Professional

When Should I seal my new concrete garage floor?

Faster if the garage floor experiences heavy vehicle and foot traffic. It would need to be reapplied every couple of years or so. Sealing products can not be used on newly poured concrete. Homeowners would have to wait 28 to 30 days when the concrete has completely cured.

David

User

How thick should a polished concrete floor BE?

about 3 to 5 mmThey typically provide a surface layer about 3 to 5 mm thick. Precautions need to be taken to protect surrounding areas and finishes from the fine airborne particles, and breathing masks should be worn.

Minh Nguyên

User

How much would it cost to pour a 30x30 concrete slab?

A typical concrete slab will cost between $113 and $126 per cubic yard (27 cubic feet) or $5.35 to $6.17 per square foot on average. Four to eight inch thick concrete slabs are mainly used for driveways, patios, sidewalks, and garage floors.

kasravnd

User

How thick should a concrete fire pit be?

The optimal size for a fire pit is between 36 and 44 inches inside diameter. That will create enough room for a healthy fire but still keep gatherers close enough to chat. As an added precaution, the fire pit should be lined with a thick steel ring like the ones used for park campfires.

Kelvin Lawrence

User

How thick should a concrete slab be for a pole barn?

4”Thickness – The industry standard for a residential pole barn, where you are storing lawn mowers, toys, or regular vehicles, is reinforced concrete floor that is 4” thick. If you have heavier equipment, you may want to consider flooring up to 6” thick for better wear and tear.

Cássio Lacerda

Guest

How thick should concrete be for 2 post lift?

4 inchesHere are our tips for making sure your installation is an uplifting experience. Some of manufacturers standards for a 2-Post and 4-Post Lifts require a minimum 4 inches of reinforced concrete slab to be safely installed.

Grzegorz Kaczan

Guest

How thick should concrete resurfacer be?

1/2 inchUnlike other cement products, it is designed to be applied in very thin coats (no more than 1/2 inch thick), and its additives provide good adhesion to an existing slab. Concrete resurfacer is a very strong product, rated for a compressive strength of about 4,500 psi.

H.B.

Guest

How thick should my concrete driveway be?

four inchesAs for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.

pearpages

Guest

How much does it cost for a concrete slab for a garage?

A typical concrete slab will cost between $113 and $126 per cubic yard (27 cubic feet) or $5.35 to $6.17 per square foot on average. Four to eight inch thick concrete slabs are mainly used for driveways, patios, sidewalks, and garage floors.

CallMeStag

Guest

How thick does a concrete garage floor need to be?

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it.

Building codes offer requirements for the concrete mix, which vary by region.

The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix..

super

Guest

How thick does a concrete sidewalk need to be?

100mmSidewalks should be at least 4" (100mm) in thickness.

Simple slabs for small foundations, bases, etc., normally 4" to 6" (100mm to150mm) thick, depending on the load they must bear.

Slope the walk away from buildings to provide proper drainage..

Bart Krakowski

Guest

How thick should concrete be for a patio?

Four inches is the minimum thickness for a concrete patio. You'll want to make it six to eight inches thick if the patio will support a structure such as a gazebo or hot tub.

Mikko Ohtamaa

Guest

How thick should a concrete drive be?

For a standard driveway your sub-base should be at least 100mm deep (the same depth as the concrete), rising to 150mm if you plan to park larger vehicles on it. The hardcore sub-base needs to be in place and compacted before any ready-mix concrete arrives.

nickelpro

Guest

How thick should a concrete pool deck be?

4 inchesAs a general rule, you should not make a concrete deck less than 4 inches thick. This depth will keep the deck strong enough to withstand general wear and tear. You could choose to make the deck 6 inches thick for good results.

Chris F

Guest

How thick should oversite concrete be?

100 mmThe concrete should be at least 100 mm thick and composed of 50 kg of cement to not more than 0.11 m3 of fine aggregate and 0.16 m3 of coarse aggregate of BS 5328 mix ST2.

warvariuc

Guest

How thick does concrete need to be to not crack?

4 inchesApplied-load cracking. In residential concrete, 4 inches is the minimum thickness for walkways and patios. Garage slabs and driveways should be 5 to 6 inches thick if any heavy truck traffic is anticipated, otherwise 4 inches is adequate.

beerwin

Guest

How thick is concrete around a pool?

6 inches thickTo be structurally sound, a concrete pool shell should generally be 6 inches thick. Depending on the engineer and the soil condition, it may be more. (On top of that, the plaster interior finish should be at least ⅜ inch thick.) The pool will also need to meet the ANSI/APSP standards.

Lord

Guest

How thick should a reinforced concrete driveway be?

4 inchesFor a concrete driveway to last the life of your home, it must be well constructed. Concrete driveway slabs typically are 4 inches thick but can be up to 6 inches thick to provide additional support for large trucks and other heavy vehicle traffic. Ideally, the slab has some kind of reinforcement inside.

Geoffrey Wiseman

Guest

How thick should concrete base be for oil tank?

Where concrete slabs are used, they should be at least 42mm* (recommended 50mm) thick.

The base should extend at least 300mm beyond the widest points of the oil tank and fully support the base of the oil tank in its entirety..

Sachila Ranawaka

Guest

Is sealed concrete waterproof?

Sealing concrete repels water and extends its life. If you have a concrete patio, garage, or driveway, sealing the concrete should be part of the initial conditioning of the surface, and should be done periodically over the life of the concrete.

Synchro

Guest

How many inches of concrete do I need for a garage?

fourThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix.

rdas

Guest

How much does a concrete garage floor cost UK?

The garage base calculator can calculate costs within a range of £5 – £12 per square foot of concrete laid at 4″ thick (100mm), which is typical for different areas around the UK. Please note – these are NOT quoted prices as there are many factors that can influence the cost of laying concrete, such as…

Sreeram TP

Guest

How thick should a cement garage floor be?

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix.

Mohammad Nurdin

Guest

How thick should concrete be for a garage floor?

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix.

Anurag Dabas

Guest

How thick should plaster mix be?

You should aim for a thickness of around 1–2mm.

The plaster you have mixed should last around 40 minutes before starting to set.

Aniruddha Das

Guest

How thick should self-leveling concrete be?

QUIKRETE® Fast-Setting Self-Leveling Floor Resurfacer (No. 1249-51) can be installed from 1-1/2 inch (38 mm) thick to a feather edge, although a ¼ inch (6.3 mm) minimum thickness is required for heavy traffic areas.

Gakis41

Guest

How big can a concrete slab be without expansion joints?

Usually, expansion joints should be no farther apart than 2 to 3 times (in feet) the total width of the concrete (in inches). So for a 4 inch thick concrete slab, expansion joints should be no more than 8 to 12 feet apart.

drAlberT

Guest

How thick is a concrete driveway?

75-100mmConcrete paths should be 75-100mm thick, whereas drives, garage bases or hardstandings should be at least 100mm thick. For heavier use, such as large vans, use a 150-200mm thick concrete slab.

Mohamed ElKalioby

Guest

How thick should a concrete driveway be NZ?

100 mmHow thick should a concrete driveway be laid to.

A minimum of 100 mm is recommended.

Thickness is a major factor in determining the driveway's structural capacity..

Rotem

Guest

How thick should a concrete garage floor be?

Standard Thickness The standard concrete garage floor is six inches thick and, with use of proper control joints, should be thick enough to withstand normal use.

alpha89

Guest

How thick should a concrete shower pan be?

Thickness for Concrete Shower Pan – Base Layer The shower pan base mortar layer thickness should be approximately ½ to 1 inch thick. Since the shower floor already has a pre-slope, just apply a base mortar layer that has an even thickness throughout the shower floor area.

Raphael Rafatpanah

Guest

How thick should a concrete sunroom be?

Four inches is the minimum thickness for a concrete patio.

You'll want to make it six to eight inches thick if the patio will support a structure such as a gazebo or hot tub..

mfulton26

Guest

How thick should a load bearing concrete wall be?

Therefore I recommend that all the walls should be at least 9 inch thick. 4.5-inch thick walls are not structurally safe if they are beyond 7 feet in height or carry some imposed load.

EdChum

Guest

How thick should a stamped concrete patio be?

four inchesHow thick is stamped concrete? Our standard slab is a minimum of four inches. Some situations will require us to pour six inches of concrete, and this would be discussed before the project takes place.

Jiaaro

Guest

How many inches thick should a concrete driveway be?

four inches thickAs for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.

kdau

Guest

How much concrete do I need for a 30x40 pole barn?

The average cost to pour a 30x40 concrete slab that is 6” thick with metal rebar reinforcements is between $8,196 and $12,384. This cost is based on a general purpose use such as a garage, whereas a foundation for a structure may cost more. Click to see full answer.