Best answer

Standard sledgehammers measure between 7 and 15 pounds. Typical projects for a standard-size sledgehammer include removing walls, breaking concrete, and other DIY demolition and renovation tasks. Heavy-duty sledgehammers have heads that weigh 16 pounds or more.

Answered by: Marcin Kunert Date created: Jun 26, 2022

How thick should my concrete slab be?

Asked By: Jacob Date created: Jun 10, 2022

4 inchesStandard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks. To prepare the base, cut the ground level to the proper depth to allow for the slab thickness.

Answered By: Ajedi32 Date created: Jun 11, 2022

How do you hang things on plaster walls?

Asked By: Jon Limjap Date created: Jun 17, 2022

Method 2 Medium to Heavy Pictures

  1. Determine where to hang your picture.
  2. Place painter's tape over the mark.
  3. Place another bit of tape below the hole.
  4. Carefully drill a hole into the plaster.
  5. Hammer an anchor into the wall.
  6. Fix the screw into your anchor.
  7. Clean the area.
  8. Hang up the picture.
Answered By: Kamafeather Date created: Jun 17, 2022

How long should cement board screws be?

Asked By: android developer Date created: Jun 10, 2022

Cement board attached to plywood or similar underlayment will hold with only 1 1/4-inch screws; for thick or heavy metal fixtures, use 1 5/8-inch screws. In general, 1 1/2-inch galvanized nails will hold the board firmly in place.

Answered By: iOS Date created: Jun 10, 2022

How thick does a concrete slab need to be for a garage?

Asked By: Jap Mul Date created: Jun 08, 2022

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region.

Answered By: Sean Vieira Date created: Jun 11, 2022

How thick does concrete need to be for heavy equipment?

Asked By: Lazar Ljubenović Date created: Jun 11, 2022

Six inchesSix inches of thickness should be more than adequate for areas where heavy equipment will be driven and parked. For lesser loads, four inches.

Answered By: Inian Date created: Jun 12, 2022

Can you throw concrete in a dumpster?

Asked By: Ben Butterworth Date created: Jun 13, 2022

Heavy materials. Extra large items like automobile tires, bricks, asphalt, concrete and mortar should not be disposed of in dumpsters. It's not safe for dumpster and landfill employees to remove such bulky items from dumpsters and into landfills.

Answered By: Cormac O'Brien Date created: Jun 13, 2022

How do you hang things on a concrete wall?

Asked By: Daniel N. Date created: Jun 14, 2022

For attaching something relatively light to concrete, it's hard to beat the speed and ease of hammer-set anchors. Each anchor consists of an unthreaded pin set into a metal sleeve. Simply drill a hole into the concrete, hold the fixture you're fastening over the hole, then use a hammer to tap the anchor into the hole.

Answered By: Steve Date created: Jun 16, 2022

How do you attach wood to concrete without a hammer drill?

Asked By: blowdart Date created: Jun 09, 2022

The Best Way to Screw into Concrete Without a Hammer DrillStart with a smaller masonry drill bit. This is going to take a lot of work. ... Transition to larger masonry drill bits. ... Work through the blockages. ... Apply water to the drill bit if it overheats.

Answered By: Steffen Ullrich Date created: Jun 10, 2022

How do you repair a concrete balcony?

Asked By: spickermann Date created: Jun 25, 2022

Step by step working instructionsRemove sanding, peeling off and incompact parts of the balcony board surface by a chisel, hammer or a cutting hammer up to faultless concrete.Carefully clean the reinforcement from rust by sanding or by a wire brush or a rotation wire brush to a metallic look.More items...

Answered By: newfurniturey Date created: Jun 25, 2022

How do I hang something on a plaster wall?

Asked By: Benjamin Muschko Date created: Jun 09, 2022

Method 2 Medium to Heavy Pictures

  • Determine where to hang your picture.
  • Place painter's tape over the mark.
  • Place another bit of tape below the hole.
  • Carefully drill a hole into the plaster.
  • Hammer an anchor into the wall.
  • Fix the screw into your anchor.
  • Clean the area.
  • Hang up the picture.
Answered By: ydaetskcoR Date created: Jun 12, 2022

Related Question Answers

Andrey Deineko

Professor

How do you attach cement board to concrete wall?

Fasten the board to the wall with 2-inch concrete screws and a hammer-action power drill with a Phillips-head screwdriver bit. Activate the hammer action on the drill before driving the screws through the board and into the wall. This is usually accomplished by flipping a toggle or switch or turning a dial.

glytching

Professor

How do you glue a broken concrete back on?

Spread a heavy layer of Loctite Metal And Concrete Epoxy on the surfaces to be joined and press the broken piece into position, leaning a heavy block against the repair until the epoxy sets. Leave undisturbed for 24 hours.

Adam Johns

Professor

How do you hang a heavy clock on a plaster wall?

Mark the wall with a pencil where the clock hangers are located in the desired location. Drill a hole and secure the screw anchors, which work in most wall types, even plaster. Tap the anchors into the wall with a hammer until they are secured in place. Place the screw inside and gently screw it into the anchor.

idz

Professor

Can I drill concrete without a hammer drill?

When a hammer drill just isn't an option, a regular drill can take its place.

It might be a bit more difficult to work a regular drill into concrete, but using a large variety of masonry drill bits and being attentive to your drill's motor can prove to be successful..

pbaranski

Professional

How much does a concrete water tank weigh?

Pre-cast concrete tanks can be delivered fully formed in sizes up to around 30,000 litres. They are extremely heavy – a 10,000 litre tank weighs around 7,000 kg.

hoefling

Professional

What's the best drill for concrete walls?

Hammer drills, also known as impact drills or percussion drills, are a powerful option suitable for drilling hard surfaces like concrete and masonry. A hammer drill is perfect for those more heavy-duty jobs around the home, from putting up shelves to securing gutters in place.

Tieme

Professional

How do you run a conduit under a concrete slab?

Select a pipe of sufficient diameter for the desired excavation width. ... Dig a small trench on each side of the concrete slab. ... Measure the width of the concrete slab. ... Push the angled end of the PVC pipe into the soil in the trench on one side. ... Tap the other end of the PVC pipe with your sledge hammer.More items...

David Schmitt

Professional

How do you drill through concrete without a hammer drill?

The Best Way to Screw into Concrete Without a Hammer DrillStart with a smaller masonry drill bit. This is going to take a lot of work. ... Transition to larger masonry drill bits. ... Work through the blockages. ... Apply water to the drill bit if it overheats.

Mark Rushakoff

User

Can you use a nail gun on plaster walls?

You can use a nail gun on plaster walls. ... It is certainly better than using a hammer and nails. Using the right care and materials, you should be able to shoot nails into your plaster walls with no problem. Plaster walls are hard and can crumble if you do not use the right size nail and technique.

serg

User

What kind of wood should I use for a concrete base?

Using 150mm x 25mm sawn and treated timber, cut the four sides of the formwork for your base. This timber should be 300mm longer than your base and 300mm wider. Lay the timber out where you want the base and using a heavy "lump" hammer bang in some 50mm x 50mm posts along the line of the timber.

Mohammad Nazari

User

When Should I seal my new concrete garage floor?

Faster if the garage floor experiences heavy vehicle and foot traffic. It would need to be reapplied every couple of years or so. Sealing products can not be used on newly poured concrete. Homeowners would have to wait 28 to 30 days when the concrete has completely cured.

Peter Krebs

User

Why is my concrete sealer bubbling?

The presence of bubbles the sealer is usually caused by a heavy application. Outgassing from the concrete surface during sealer application should be free to quickly move through a thin, wet sealer film. ... Bubbling of a sealer can also occur if application is done in hot weather, or if the concrete is in direct sun.

Alex Mamo

User

How thick should a concrete slab be for a shop?

Five to six inchesFive to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks.

To prepare the base, cut the ground level to the proper depth to allow for the slab thickness..

void

Guest

Can you drill into concrete without a hammer drill?

When a hammer drill just isn't an option, a regular drill can take its place. It might be a bit more difficult to work a regular drill into concrete, but using a large variety of masonry drill bits and being attentive to your drill's motor can prove to be successful.

Tony Andrews

Guest

How long should concrete piers dry?

about 3 daysAllow the concrete to cure for one day before constructing your deck or placing heavy weight on the footing (if standard concrete mix was used, wait about 3 days to begin construction).

Sebastian Krysmanski

Guest

Should concrete forms be oiled?

Any type of oil will prevent concrete from sticking to wood. Spray the surfaces that will face the wet concrete with a heavy saturation of oil. ... Apply a second heavy spraying of oil just before pouring concrete.

Nyambaa

Guest

What do I need for concrete repair?

You'll need a few tools, including a cold chisel, ball-peen hammer or 8-pound sledge for larger areas, protective goggles and gloves. A brush and broom or hand vac is also necessary, as is a plasterer's trowel and pointing trowel. If you're resurfacing steps and slabs, you'll need an edger as well.

mipadi

Guest

How do you break up concrete with a sledge hammer?

Strike the Concrete Grasp the sledgehammer handle with your dominant hand close to the head and your other hand toward the end of the handle. Use an arching motion to lift the hammer as high as possible, but not directly over your head, then let it fall as you slide the dominant hand down the handle.

DeepSpace

Guest

How do you drill a hole in a concrete beam?

If you're just drilling one or two holes for a small project, a regular drill is fine. However, drilling concrete is much easier with a hammer drill, or a rotary hammer for large jobs. These tools fracture the concrete through rapid hammering, then drill to scoop out the broken material.

Sparky

Guest

How thick does a concrete garage floor need to be?

four-inchesThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it.

Building codes offer requirements for the concrete mix, which vary by region.

The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix..

Aminah Nuraini

Guest

Can you break concrete with a hammer drill?

Use a heavy duty hammer drill or a breaking chisel attachment in a rotary hammer to chip the concrete next to the line you sawed. Tilt the chisel so the side you will be removing cracks loose, not the side you're keeping. Gradually deepen the hole.

dm03514

Guest

Can you break up concrete with a hammer drill?

Hammer drills do not have a chiseling function and can be used to drill into a variety of materials. ... Demolition hammers can break, chip and chisel concrete, but they can't drill because there is no rotation of the bit.

Giang Le

Guest

Can you drill concrete without hammer drill?

For drilling into concrete without a hammer drill, a changeable head is vital because you cannot use a standard drill bit. Next, if you must use a regular drill, it should have variable speed and torque settings. When using concrete drill bits, you may need to adjust the speed and torque.

Josh Habdas

Guest

Can you drill into concrete with a cordless drill?

Whenever you drill through hard materials like concrete, this hammer action becomes very important. Drilling into concrete using hammer action can speed up the entire process. Whenever you go cordless drill shopping, make sure to buy a cordless drill that includes hammer action.

Harsh Bhikadia

Guest

How do you nail a concrete wall?

Drill a pilot hole into the concrete wall, using a drill and masonry bit. The hole should be the same size in diameter as the masonry nail anchor. Insert the anchor into the hole so the top rim is flush with the surface of the wall. Hammer the nail into the anchor.

Otto Allmendinger

Guest

How thick should concrete be for heavy equipment?

6 inchesIf they will be subject to occasional use by garbage trucks, RVs or other heavy vehicles, the recommended thickness may be 6 inches or more. Parking Lots: Most parking lots will need concrete pavement that is at least 6 inches deep. If heavyweight trucks will also be allowed, the thickness must be increased.

Gildas Garcia

Guest

Can you put concrete in a dumpster?

Heavy debris, such as: concrete, asphalt, dirt, and brick, can be thrown in most dumpsters, however due to its weight, Express Roll-Off only allows 15 Yard dumpsters (filled 3/4 high) for these heavy materials. Asphalt roofing shingles are another category of heavy debris that can go in a dumpster.

Giorgos Myrianthous

Guest

How do I remove cement from my lawn?

Use the sledge hammer near the pry bar tip to break off more of the concrete. Remove rubble, and continue these steps, with the pry bar tip moving with the removable concrete slab edge. Progress at this point will feel slow, but stick with it. Keep removing the rubble, and using the pry bar and sledge hammer in tandem.

Alapan Das

Guest

How do you break a concrete rotary hammer?

Use a heavy duty hammer drill or a breaking chisel attachment in a rotary hammer to chip the concrete next to the line you sawed.

Tilt the chisel so the side you will be removing cracks loose, not the side you're keeping.

Gradually deepen the hole..

sourav pandit

Guest

How long does it take to jackhammer a concrete slab?

Just take a few whacks at the slab with a 12-lb. sledgehammer (Photo 1). Within 10 minutes, you'll know whether it's a job for a sledge or a jackhammer. Consider renting an electric jackhammer to make the job easier.

rixo

Guest

How thick does concrete need to be to not crack?

4 inchesApplied-load cracking. In residential concrete, 4 inches is the minimum thickness for walkways and patios. Garage slabs and driveways should be 5 to 6 inches thick if any heavy truck traffic is anticipated, otherwise 4 inches is adequate.

David Hellsing

Guest

How thick should a reinforced concrete driveway be?

4 inchesFor a concrete driveway to last the life of your home, it must be well constructed. Concrete driveway slabs typically are 4 inches thick but can be up to 6 inches thick to provide additional support for large trucks and other heavy vehicle traffic. Ideally, the slab has some kind of reinforcement inside.

Victor Eronmosele

Guest

How long does it take for 4 inches of concrete to cure?

After 7 days, the concrete will have gained around three quarters of its compressive strength, but you should refrain from driving vehicles or heavy machinery over the surface until after the 28 day mark. For domestic mixes – driveways, for example – you can expect the concrete to be set within 24-48 hours.

Shady Aziza

Guest

Is concrete harder than asphalt?

Concrete is a much harder surface than asphalt or macadam. It's the worst commonly encountered surface that you can run on and should be avoided like the plague. To compare the "hardness" of concrete and asphalt, hit each surface with a hammer and see how it feels to your hand and arm.

McGarnagle

Guest

Should you use concrete for fence posts?

Concrete is the most secure material for setting fence posts, especially if you have sandy soil. Gravel may be okay with dense, clay-heavy soil, but in looser soil, concrete is the only thing that will truly keep your fence posts stuck in place.

kingston

Guest

How do you remove a plaster wall?

Tap the plaster on a wall with a hammer or a 3-pound sledgehammer until the plaster cracks and crumbles. A small sledgehammer makes the job easier, but it requires some caution. If you use a sledge, tap the wall lightly; don't bash it with a great deal of force.

norok2

Guest

How do you remove a toilet from a concrete floor?

Use a small hammer and chisel to carefully crack the back of the pan near the joint to the waste pipe. This will separate the pan spigot from the rest of the pan. Then smash the pan away from the pipe with a bigger hammer and clean off any cement on the floor.

brian d foy

Guest

How do you remove old plaster ceilings?

Remove the plaster using a claw hammer or similar and a stout trowel. Working in front of yourself, tap the plasterwork with your hammer to break it up and if it doesn't drop away, keep tapping it and then either use the claw on your hammer or lever the plasterwork off with the trowel.

Behemoth

Guest

Is polished concrete cheaper?

For all polished concrete projects, the cost will depend on how much heavy grinding is needed. A light grind will be cheaper than a heavy grind. A light grind with a polish achieves a nice-looking floor and is the most economical option.

user3142695

Guest

How long should a concrete garage floor last?

For example, a professionally installed epoxy flooring system can last up to 30 years in a residential and light traffic area, but the flooring system may only last up to 15-20 years when placed in heavy-duty commercial and industrial facilities due to heavy traffic simply wearing the floor down rapidly..

chandil03

Guest

How long until concrete is full strength?

approximately 25-28 daysHowever, concrete reaches its full strength after approximately 25-28 days. You should be able to walk and perform normal tasks on concrete one week after its application. However, the concrete will only be at around 70-70% of its full strength, so driving heavy machinery on it is not advised during this time.

Sinh Nguyen

Guest

How many inches of concrete do I need for a garage?

fourThe concrete slab should be four-inches thick at least; it needs to be thicker if heavy equipment will rest on it. Building codes offer requirements for the concrete mix, which vary by region. The standards are expressed in terms of "compressive strength," which boils down to the amount of water used in the mix.

Thomas Dickey

Guest

How many inches thick should a concrete patio be?

4 inchesMinimum standards for the construction of concrete patios will generally apply to ensure that safety is maintained. The minimum thickness of any concrete slab is 4 inches. However, if the concrete patio will have heavy features added to it, you may want to thicken it to 6 or 8 inches.

Hai Vu

Guest

What is the best concrete crack sealer?

QUIKRETE Concrete Repair, QUIKRETE Gray Concrete Crack Seal or QUIKRETE Self-Leveling Polyurethane Sealant may be used. Widen the crack using a chisel and hammer to a minimum of ¼ inch and break away any deteriorating concrete (the edges of the crack should be vertical or beveled in an inverted “v”).