Best answer

All concrete consists of three simple ingredients: cement, aggregates like sand or gravel, and water. It's the proportions of each that determine the strength of the project. For a 10 x 10 slab, we'd suggest a mix with a capacity of about 4,000 pounds per square inch, or psi.

Answered by: ryanve Date created: Jun 25, 2022

How many bags of cement do I need for a 10x10 slab?

Asked By: Connor Low Date created: Jun 20, 2022

For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags. If we add an extra 10%, that's an extra 8 60-pound bags or 6 80-pound bags.

Answered By: Mechanical snail Date created: Jun 20, 2022

How many bags of cement are needed to plaster a room?

Asked By: Koen. Date created: Jun 07, 2022

6 bags

Answered By: M.Innat Date created: Jun 07, 2022

Is cement board needed for floor tile?

Asked By: Jon Purdy Date created: Jun 22, 2022

In short, tile and grout are not inherently waterproof. Cement backer board is often used as a tile base on plywood or OSB subfloor. Cement backer board on concrete as a subfloor or underlayment is usually not recommended or needed. In most cases, you can apply tile directly to the concrete.1 Dec 2019

Answered By: knittl Date created: Jun 25, 2022

How much concrete is needed for a 10x10 room?

Asked By: Alexander Oh Date created: Jun 24, 2022

14.19 cuft of cement 2. 28.38 cuft of fine aggregate.

Answered By: Paul Morgan Date created: Jun 24, 2022

How deep should I dig for a concrete slab?

Asked By: pguardiario Date created: Jun 10, 2022

Add 2 inches to the depth for gravel if the soil is normally moist or has a high concentration of clay. Most concrete slabs will sit 1 to 2 inches higher than the dirt and 2 to 3 inches below the surface of the dirt, making the needed depth of the hole 3 to 5 inches.

Answered By: Julia Passynkova Date created: Jun 10, 2022

How thick should cement board be under tile floor?

Asked By: Dmitriusan Date created: Jun 16, 2022

Floors: A 1/4-inch minimum thickness is needed, but thicker panels are also fine. Walls: Use 1/2-inch or 5/8-inch-thick cement board, not 1/4-inch. The extra thickness is needed to span the studs and provide a solid base for the tile.

Answered By: Andriy Ivaneyko Date created: Jun 18, 2022

How much concrete do I need for a 10x10 slab?

Asked By: derfred Date created: Jun 14, 2022

For a 10 x 10 slab, we'd suggest a mix with a capacity of about 4,000 pounds per square inch, or psi. This is basic for residential projects, and it can withstand traffic and support heavy loads.

Answered By: Jordon Phillips Date created: Jun 14, 2022

How much does it cost for a 30x40 concrete slab?

Asked By: Mureinik Date created: Jun 21, 2022

Concrete Slab Cost CalculatorSize (in feet)Approximate Cost20x40$4,80030x30$5,40030x40$7,20030x50$9,00010 more rows

Answered By: SkyWalker Date created: Jun 23, 2022

How much would a 40x60 concrete slab cost?

Asked By: Ben Y Date created: Jun 17, 2022

How much does a 40×60 concrete slab cost? It would be about $8,500 to $12,000 for a 40×60 foot concrete slab, 6 inches thick. That's based on national averages of around $5 per square foot for a fully engineered, finished concrete slab, including labor and materials.

Answered By: Pure.Krome Date created: Jun 20, 2022

How many bags of concrete do I need for a 8x8 slab?

Asked By: Freesnöw Date created: Jun 21, 2022

How many concrete bags would I need for a 8 ft x 8 ft x 6" slab? 54 x 80lb Concrete bags. How much does it cost to pour a 8'x8' x6" slab? Ready-mix costs approx $277.86.

Answered By: DeepSpace Date created: Jun 21, 2022

Related Question Answers

Babken Vardanyan

Professor

How much does it cost for a 12x12 concrete slab?

To pour a typical 10x10 concrete slab will cost $670 to $930, a 12x12 slab for a patio will cost $796 to $1,476, a 20x24 driveway slab runs between $1,440 and $3,360, and a 24x24 slab for a garage will cost $3,058 to $5,944. Get free estimates from concrete companies near you.

diegoveloper

Professor

How much cement do I need for a 20x20 slab?

With a brief look, a 20x20 area at 6 inches deep, you would need approximately 10.52 tons or 7.41 cubic yards of gravel. Concrete reinforcing is also recommended in high traffic areas and medium to large areas.

Grzegorz Żur

Professor

How much does it cost to pour a 24x24 concrete slab?

A typical 24x24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete..

qwerty_so

Professor

Are concrete expansion joints necessary?

Expansion joints are virtually never needed with interior slabs, because the concrete doesn't expand that much—it never gets that hot. Expansion joints in concrete pavement are also seldom needed, since the contraction joints open enough (from drying shrinkage) to account for temperature expansion.

JohnTESlade

Professor

Can I extend a concrete slab?

Making sure that the foundation for the extension is well compacted and onto good material. Cut back and scable the joint with the existing 10x10 slab so that there is a good bond when the new concrete is cast. Drill and fix dowel bars into the existing slab across the joint with the extension.

Andrew Marshall

Professional

How do you level an existing concrete slab?

Apply a coating of the compound to the identified low areas on the concrete slab, smoothing it out with a trowel. Work at a rapid pace since the leveling compound will dry in less than 1 hour after being mixed with water. Finish coating the slab as needed with the compound mixture.

Emil Vikström

Professional

How much does a 10x10 concrete slab weigh?

A 10' x 10' pad of concrete 4 inches thick is a little over 1 cubic yard weighs approximately 4,400 pounds. If you want to calculate the weight of concrete by cubic foot, just divide the cubic yard weight by 27. Coincidentally, the weight of one cubic foot of concrete weighs about 150 pounds.

Webert Lima

Professional

How much concrete do I need for a 24x24 garage?

Average Cost To Pour Concrete To pour a typical 10x10 concrete slab will cost $670 to $930, a 12x12 slab for a patio will cost $796 to $1,476, a 20x24 driveway slab runs between $1,440 and $3,360, and a 24x24 slab for a garage will cost $3,058 to $5,944.

Romain Guy

Professional

How much should a 10x10 concrete slab cost?

Average Cost To Pour Concrete To pour a typical 10x10 concrete slab will cost $670 to $930, a 12x12 slab for a patio will cost $796 to $1,476, a 20x24 driveway slab runs between $1,440 and $3,360, and a 24x24 slab for a garage will cost $3,058 to $5,944.

spottedmahn

Professional

How much concrete is needed for a fence post?

To calculate how much concrete you need, you need to know the post size you are going to use and how many posts you are installing.

Your post diameter and height determine how big each hole needs to be.

As stated above, fence post holes should be 3 times the diameter of your post and 1⁄3 as deep as your post..

Axeman

User

How many bag of cement do I need?

For concrete, the formula for volume is as follows: length x width x thickness. To determine how many bags of concrete you will need, divide the total cubic yards needed by the yield.

Jarek Tkaczyk

User

How much concrete is needed for an ICF block?

STANDARD ICFSTANDARD ICF$13.95,$15.95 or $17.95Concrete$100.00 Per yard (1 yard fills 10.5 blocks)Labor$30.00 per hour, 5 blocks per man hourRe-bar$.30 per footPump$250 minimum, Plus $3.00 per yard1 more row

TheHippo

User

Can you put footings under concrete slab?

edit - To put footings under the slab, you can cut holes wherever needed, excavate for footings (Sonotubes or concrete piers or similar) and then patch the concrete slab.

alkasm

Guest

How much does it cost to cement a pole barn?

It would be about $8,500 to $12,000 for a 40×60 foot concrete slab, 6 inches thick. That's based on national averages of around $5 per square foot for a fully engineered, finished concrete slab, including labor and materials.

sakra

Guest

How much does it cost to grind a concrete floor?

Economical: You can expect to pay between $3 and $12 per square foot for polished concrete, depending on your location and the complexity of the project. Polished concrete pricing is dependent upon how many levels of grinding are needed to get the floor to a smooth surface.

David C. Rankin

Guest

How much would a 12x10 concrete slab cost?

Average Cost To Pour Concrete To pour a typical 10x10 concrete slab will cost $670 to $930, a 12x12 slab for a patio will cost $796 to $1,476, a 20x24 driveway slab runs between $1,440 and $3,360, and a 24x24 slab for a garage will cost $3,058 to $5,944..

Heath Borders

Guest

Can you extend an existing concrete slab?

Your best bet for a good finish relies on doing three things: Making sure that the foundation for the extension is well compacted and onto good material. Cut back and scable the joint with the existing 10x10 slab so that there is a good bond when the new concrete is cast.

Eugene

Guest

Can you add footers to a concrete slab?

edit - To put footings under the slab, you can cut holes wherever needed, excavate for footings (Sonotubes or concrete piers or similar) and then patch the concrete slab.

TomAugspurger

Guest

How much concrete do I need for Paver molds?

For a customized look, purchase powdered cement coloring to add to the concrete mixture. Here's how we made our lovely walkway with the mold. Determine the amount of concrete material needed for the project. Quikrete recommends one 80-pound bag of concrete for every 2 feet of walkway.

fsimonjetz

Guest

How do you calculate the number of bags of cement is needed?

For concrete, the formula for volume is as follows: length x width x thickness. To determine how many bags of concrete you will need, divide the total cubic yards needed by the yield. Use the following yields per each bag size: 40 pound bag yields .011 cubic yards.

Ajay Kumar

Guest

How do you start a cement factory?

Cement is the basic raw material of concrete and is a very important building material....Clarify Your Production Scale and Cement Type. ... Find the Most Appropriate Location for Your Cement Factory. ... Design the Cement Factory. ... Purchase Needed Equipment. ... Factory Construction & Equipment Installation. ... Staff Recruitment & Training.

Vlad Mihalcea

Guest

Is polished concrete cheaper?

For all polished concrete projects, the cost will depend on how much heavy grinding is needed. A light grind will be cheaper than a heavy grind. A light grind with a polish achieves a nice-looking floor and is the most economical option.

PMF

Guest

How many bags of cement do I need for 10x10?

Using a Concrete Calculator You'll also get the number of 40-pound, 60-pound, or 80-pound bags of concrete are needed for the project. For example, a 10′ x 10′ slab that is 4″ thick will need an estimated 1.23 yards3 or 75 60lb bags of concrete and will cost roughly $140.

lostInTransit

Guest

How many bags of concrete do I need for a 10x10 slab 4 inches thick?

The volume of concrete required for a 10- by 10-foot slab depends on the diameter of the slab.

For a 4-inch slab, either eight 60-pound or six 80-pound bags are required, while for a 6-inch slab, either 12 60-pound or nine 80-pound bags are necessary..

serv-inc

Guest

How much cement mix do I need?

To determine how many bags of concrete you will need, divide the total cubic yards needed by the yield. Use the following yields per each bag size: 40 pound bag yields .011 cubic yards. 60 pound bag yields .017 cubic yards.

Lucio Paiva

Guest

How much does a 12x12 concrete slab weigh?

How much does a 12x12 concrete slab weigh? The weight of concrete is approximately 150 pounds per cubic foot, or 4,050 pounds per cubic yard. The formula for calculating the weight of concrete is: Length (in feet) x Width (in feet) x Thickness (in inches) /12 x 150 = weight (in pounds).

ams

Guest

How much does a 24x30 concrete slab cost?

On average, the material alone costs anywhere between $5.38 to $6.19 per square foot. How do you calculate concrete for a slab?...How much does a 24x30 concrete slab cost?Concrete Slabs CostsZip CodeBasicBestConcrete Slabs – Total Average Cost per square foot$6.88$14.612 more rows•Apr 16, 2020

talat

Guest

How much does a 30x30 concrete slab cost?

How much is the cost of a 30x30 concrete slab? A 30x30 foot concrete slab costs about $5,400 including installation. This is for 6-inch thickness, but can go up or down depending on what your concrete pro recommends.

L3viathan

Guest

How much does it cost for a 24x24 concrete slab?

A typical 24x24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.

blueberryfields

Guest

How much does it cost to grind concrete for epoxy?

Economical: You can expect to pay between $3 and $12 per square foot for polished concrete, depending on your location and the complexity of the project. Polished concrete pricing is dependent upon how many levels of grinding are needed to get the floor to a smooth surface.

Adrian T

Guest

How much is a 24x24 concrete slab?

A typical 24x24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.

Mark Ransom

Guest

How do you calculate concrete for a round hole?

To find cubic metres needed to fill a round holeEXAMPLE: How much concrete is needed to fill 5 holes 1200mm deep and 1050mm round?ANSWER: One hole takes 1.039 cubic metres, therefore 5 holes = 5 x 1.039 = 5.195. ( say 5.2 cubic metres)NOTE: When the Diameter of a hole is doubled, it takes 4 times more concrete.

BENY

Guest

How many 80lb bags of concrete do I need for a 10x10 slab?

For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags. If we add an extra 10%, that's an extra 8 60-pound bags or 6 80-pound bags. Whatever the size of your project, use the formula above to calculate how much concrete you'll need!

Rolando

Guest

How much does it cost for a 10x10 concrete slab?

To pour a typical 10x10 concrete slab will cost $670 to $930, a 12x12 slab for a patio will cost $796 to $1,476, a 20x24 driveway slab runs between $1,440 and $3,360, and a 24x24 slab for a garage will cost $3,058 to $5,944.

skiphoppy

Guest

How much is a concrete slab per square foot?

A slab of concrete typically costs about $4 per square foot for materials. On average, a concrete slab cost about $6 per square foot with labor. Including labor, the cost of a concrete pad can range between $4 and $8 per square foot.

Bala R

Guest

How many bags of concrete do I need for a 10x10?

The volume of concrete required for a 10- by 10-foot slab depends on the diameter of the slab. For a 4-inch slab, either eight 60-pound or six 80-pound bags are required, while for a 6-inch slab, either 12 60-pound or nine 80-pound bags are necessary.